AKAI MFC42 Owner's Manual

Cover page of AKAI MFC42 Owner's Manual

Owner's Manual for AKAI MFC42, downloadable as a PDF file.

Manual details

  • Immediate download after payment.
  • Delivered as a PDF file.
  • The manual has 33 pages
  • File size: 0.76 MB
  • Available language versions: English
  • Different language versions may vary sligthly in file size and page count.

We guarantee that...

  • our manuals are complete,
  • our manuals are checked with antivirus,
  • We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

Thumbnail of page 1Thumbnail of page 2Thumbnail of page 3Thumbnail of page 4
Thumbnail of page 5Thumbnail of page 6Thumbnail of page 7Thumbnail of page 8
Thumbnail of page 9
background image
Analog Filter Module
background image
Analog Filter Module
background image
WARNING!!
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
1-En
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE SYMBOLS ARE RULED BY UL STANDARDS (U.S.A.)
The lightning flash with arrowhead symbol , within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure; that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intented to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
5B-En
9/25/2001 Rev. 4
background image
i
WARNING
WARNING: WHEN USING ELECTRIC PRODUCTS, BASIC PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE FOLLOWING:
WARNING
The MFC42 is designed to be used in a standard household environment.
Power requirements for electrical equipment differ from area to area. The operating voltage of this
MFC42 is preset at the factory according to its intended destination. However, before connecting,
check to see that the VOLTAGE SELECTOR on the rear panel is set to the correct voltage for your
area. If not, please set it correctly before plugging in the power cord. If in doubt, consult a qualified
electrician or AKAI professional dealer.
120 VAC
@ 60 Hz for USA and Canada
230 VAC
@ 50 Hz for Europe
If the VOLTAGE SELECTOR is not set correctly for your area:
Confirm that the power cord is disconnected.
Remove the VOLTAGE SELECTOR with a screw driver and
replace it so that the correct voltage for your area is lined with
the marker. Also, change the fuse according to the chart
indicated on the rear panel as necessary.
PROTECTING YOURSELF AND THE MFC42
·
Never touch the AC plug with wet hands.
·
Always disconnect the MFC42 from the power supply
by pulling on the plug, not the cord.
·
Allow only an AKAI professional dealer or qualified professional engineer to repair or reassemble
the MFC42. Apart from voiding the warranty, unauthorized engineers might touch live internal
parts and receive a serious electrical shock. There are no serviceable parts inside.
·
Do not put, or allow anyone to put any object, especially metal objects, into the MFC42.
·
Use only a household AC power supply. Never use a DC power supply.
·
If water or any other liquid is spilled into or onto the MFC42, disconnect the power, and call your
dealer.
·
Make sure that the unit is well-ventilated, and away from direct sunlight.
·
To avoid damage to internal circuitry, as well as the external finish, keep the MFC42 away from
sources of direct heat (stoves, radiators, etc.).
·
Avoid using aerosol insecticides, etc. near the MFC42. They may damage the surface, and
may ignite.
·
Do not use denatured alcohol, thinner or similar chemicals to clean the MFC42. They will damage
the finish.
·
Modification of this equipment is dangerous, and can result in the functions of the MFC42 being
impaired. Never attempt to modify the equipment in any way.
·
Make sure that the MFC42 is always well-supported when in use (either in a specially-designed
equipment rack, or on a firm level surface).
·
When installing the MFC42 in a 19" rack system, always allow 1U of ventilated free space
above it to allow for cooling. Make sure that the back of the rack is unobstructed to allow a clear
airflow.
·
In order to assure optimum performance of your MFC42, select the setup location carefully,
and make sure the equipment is used properly. Avoid setting up the MFC42 in the following
locations:
1. In a humid or dusty environment
2. In a room with poor ventilation
3. On a surface which is not horizontal
4. Inside a vehicle such as a car, where it will be subject to vibration
5. In an extremely hot or cold environment
background image
ii
WARNING
For U.K. Customers Only
WARNING
THIS APPARATUS MUST BE EARTHED
IMPORTANT
This equipment is fitted with an approved non-rewireable UK mains plug.
To change the fuse in this type of plug proceed as follows:
1) Remove the fuse cover and old fuse.
2) Fit a new fuse which should be a BS1362 5 Amp A.S.T.A or BSI approved type.
3) Refit the fuse cover.
If the AC mains plug fitted to the lead supplied with this equipment is not suitable for your type of
AC outlet sockets, it should be changed to an AC mains lead, complete with moulded plug, to the
appropriate type. If this is not possible, the plug should be cut off and a correct one fitted to suit the
AC outlet. This should be fused at 5 Amps.
If a plug without a fuse is used, the fuse at the distribution board should NOT BE GREATER than
5 Amp.
PLEASE NOTE:
THE SEVERED PLUG MUST BE DESTROYED TO AVOID A POSSIBLE
SHOCK HAZARD SHOULD IT BE INSERTED INTO A 13 AMP SOCKET
ELSEWHERE.
The wires in this mains lead are coloured in accordance with the following code:
GREEN and YELLOW
-- Earth
BLUE
-- Neutral
BROWN
-- Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug, please proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal which is
marked with the letter E or with the safety earth symbol
or coloured GREEN or coloured
GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked
with the etter L or coloured RED.
THIS APPARATUS MUST BE EARTHED
Ensure that all the terminals are securely tightened and no loose strands of wire exist.
Before replacing the plug cover, make certain the cord grip is clamped over the outer sheath of the
lead and not simply over the wires.
6D-En
background image
iii
WARNING
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
·
Reorient or relocate the receiving antenna.
·
Increase the separation between the equipment and receiver.
·
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
·
Consult the dealer or an experienced radio/TV technician for help.
21B-En
AVIS POUR LES ACHETEURS CANADIENS DU MFC42
Le présent appareil numérique n'ément pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Class B prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
27-F
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
27-En
VENTILATION
Do not prevent the unit's ventilation, especially by placing the unit on the soft carpet, in a
narrow space, or by placing objects on the unit's chassis--top, side, or rear panels. Always
keep the unit's chassis at least 10 centimeters from any other objects.
31C-En
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER
FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
32-En
COPYRIGHT NOTICE
The AKAI MFC42 contains and uses software in ROMs. This software, and all related
documentation, including this OperatorOs Manual, contain proprietary information which is
protected by copyright laws. All rights are reserved. No part of the software or its documentation
may be copied, transferred or modified. You may not modify, adapt, translate, lease, distribute,
resell for profit or create derivative works based on the software and its related documentation or
any part thereof without prior written consent from AKAI professional M.I. Corp., Yokohama,
Japan.

Reviews

There are no reviews of this manual yet.

Related Products

Cover page of AKAI TV1402CK Service Manual

This manual has 6 pages, file size: 0.63 MB. It's available in languages: English.

Cover page of AKAI AJW238L/S Service Manual

This manual has 30 pages, file size: 6.22 MB. It's available in languages: English.

Cover page of AKAI AP-Q55/C Service Manual

This manual has 61 pages, file size: 9.36 MB. It's available in languages: English.

Cover page of AKAI 202D-SS Service Manual

This manual has 63 pages, file size: 18.61 MB. It's available in languages: English.

Cover page of AKAI AAM33 Service Manual

This manual has 46 pages, file size: 14.49 MB. It's available in languages: English.