CAUTION:
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radia-
tion exposure.
In compliance with Federal Regulations, the following are repro-
ductions of labels on, or inside the product relating to laser prod-
uct safety.
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI,
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS NO. 21 CFR
1040.10, CHAPTER 1, SUBCHAPTER J.
Location: Back Panel
For the U.S.A.
For Canada
NOTICE: This Class B digital apparatus complies with
Canadian ICES-003.
Note to CATV system installer
This reminder is provided to call the CATV system installer's at-
tention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical.
For the U.S.A.
Caution on condensation
Before transporting or moving this unit, carry out the
following operations.
1. Set the POWER ON/OFF switch to the ON
without loading a disc.
2. Wait a few seconds and verify that the display
shown appears.
"NO DISC"
3. Set the POWER ON/OFF switch to OFF.
Note related to transportation and movement
Condensation (of dew) may occur inside the unit when there is a great
difference in temperature between this unit and the outside. This unit
may not function properly if condensation occurs. In this case, leave
the unit for a few hours and restart the operation after the condensa-
tion has dried up.
Be specially cautious against condensation in the following circum-
stances:
When this unit is carried from one place to another across a large
difference in temperature, when the humidity in the room where
this unit is installed increases, etc.
Operation to reset
The microprocessor may fall into malfunction
(impossibility to operate erroneous display, etc.)
when the power cord is unplugged while power is
ON or due to an external factor.
In this case, switch off the power, wait for several
seconds, and then switch the power on again.
The marking of products using lasers
(For countries other than U.S.A. and Canada)
The marking this product has been classified as Class 1. It
means that there is no danger of hazardous radiation outside
the product.
Location: Back panel
CLASS 1
LASER PRODUCT
Video cord (Yellow)(1)
(E30-7341-08)
Loop antenna (1)
(T90-0917-08)
FM indoor antenna (1)
Remote control unit (1)
(A70-1685-08)
Batteries
(R03/AAA) (2)
Speaker cords (6) *
(For Europe)
(T90-0916-08)
(For U.S.A., Canada
and Australia)
(T90-0915-08)
Accessories for speaker part
(For DVT-6300 and DVT-7300)
Length
For Front (2)
4.5 m (177-3/16")
For Center (1)
3 m (118-1/8")
For Rear (2)
8 m (314-15/16")
For Subwoofer (1)
4.5 m (177-3/16")
Cushion (15) *
(Small : 11 pcs 1 sheet)
(Big : 4 pcs 1 sheet)
* See speaker's manual.
DVR-6300
2
CONTENTS / ACCESSORIES / CAUTIONS
CONTENTS / ACCESSORIES / CAUTIONS ...............2
PARTS DESCRIPTIONS .............................................3
PC BOARD ..................................................................4
SCHEMATIC DIAGRAM ............................................15
EXPLODED VIEW .....................................................25
PARTS LIST...............................................................27
SPECIFICATIONS .....................................................34
CONTENTS
ACCESSORIES
CAUTIONS
SYSTEM CONFIGURATIONS
SYSTEM
RECEIVER
SPEAKER
SPEAKER
DVT-6300-H
DVR-6300
KSW-6300-H
-
DVT-6300-S
DVR-6300
KSW-6300-S
-
DVT-7300
DVR-6300
KSW-7300
-
DVT-8300
DVR-6300
KS-908HT
SW-18HT
