KENWOOD K-ES01 Owner's Manual

KENWOOD K-ES01 Owner's Manual
0 Rating(s)
Read reviews

Owner's Manual for KENWOOD K-ES01, downloadable as a PDF file.

Manual details

Immediate download after payment.
Delivered as a PDF file.
The manual has 2 pages
File size: 0.51 MB
Available language versions: Japanese, English
Different language versions may vary sligthly in file size and page count.

We guarantee that...

our manuals are complete,
our manuals are checked with antivirus,
We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

Thank you for purchasing this product.

Please read this instruction manual thoroughly before installing speakers, and

install speakers correctly.

Tools required for installation Phillips screwdriver, Flat-head screwdriver, Clip driver, Pliers, Nippers, Wrench,

Electric hand drill and bits, Cutting knife, Electrical tape, Scissors, Felt-tip pen

Safety caution

Be sure to observe the warning and caution provided below as they are critical for your safety.

The meanings of the symbols are as follows.

SEPARATE CUSTOM FIT SPEAKER

K-ES01

INSTRUCTION MANUAL

KENWOOD CORPORATION

B54-1210-20 (FHP)

Installation cautions

If the product is handled erroneously by ignoring the instruction of this mark,

fatal hazard or serious injury on human body may result.

If the product is handled erroneously

by ignoring the instruction of this

mark, injury on human body, or dam-

age of product may result.

CAUTION

Work depending to instruction manual.

When installing or wiring the product,

be sure to follow strictly the instruction

and installation manuals of the product.

(If the instructions are not observed

strictly, the product may be displaced

and hit you during braking and there

may also be a risk of electric shock or

fire hazard.)

Please read thoroughly.

Be careful not to damage the tank and

electric wiring.

In case the product is installed by mak-

ing holes on the vehicle chassis, be

careful never to damage the gasoline

tank, piping, electric wiring or other

parts of the vehicle.

(Otherwise fire hazard may result.)

Do not pull the cord.

When you remove the connector, please

remove and lock it with the connector

main part, without pulling the cord.

Otherwise disconnection of a cord and

poor contact may result.

Do not cut insulation tube in the middle

of a power cord.

Do not use power cord for other prod-

ucts by cutting insulation tube in the

middle of a power cord.

(Otherwise a shorting accident* may

occur, which could result in fire acci-

dent.)

Do not open the back and top covers of

the product or modify it.

(This may lead to fire hazard or other

accident.)

· For inspection and servicing, consult

your dealer or nearest KENWOOD ser-

vice agent or distributor.

· Servicing by the user may lead to fire

hazard or other accidents.

Use a fuse with the specified rating.

When the fuse is blown, first ensure that

there is no short-circuiting* between the

wired cords, then replace with a new

fuse with the capacity (Ampere value)

specified on the fuse box.

(Using other fuse than specified may

lead to fire hazard.)

· For fuse replacement, refer to the

owner's manual of your vehicle.

Please check the spec.

Use provided parts for installation.

Be sure to install a product using pro-

vided parts. When parts other than the

provided ones are used, a product may

fall off and hit the passenger while driv-

ing, causing injury or product breakage.

Inspect the vehicle after installation.

After installation of the product, be sure

to check that the brake lamps, head

lamps, direction indicators, windshield

wipers, power window, etc. of the vehi-

cle function normally.

(If any of the vehicle functions are dam-

aged due to incorrect wiring , etc., traf-

fic accident may result. )

Remove battery connection before work.

Before installing or wiring anything, be

sure to remove the cable from the nega-

tive terminal of the battery.

(Otherwise a shorting accident* may

occur, which could result in fire acci-

dent.)

Remove negative terminal.

Use proper tools for the processing

objects.

When tightening a bolt or nut, always be

sure to use the tool matching its size. If

the securing torque of a part is speci-

fied, be sure to secure it with the speci-

fied force.

(Otherwise the bolt or nut may be dam-

aged or detached during use.)

Wrap cords with protective tape.

The cords near metallic parts of the

vehicle should be protected against

sharp edge of the metallic parts by

wrapping insulating tape around them.

(If a cord is damaged, electric shock or

short-circuiting* as well as fire hazard

may result.)

* Short-circuiting and shorting accident

Short-circuiting refers to the direct connection between the positive and negative poles of electricity. This may occur when a stripped cord (electric wiring) comes in

contact with another cord or metallic part of vehicle. Short-circuiting may produce spark, which may be caught by surrounding objects and result in fire hazard.

Cautions on use

WARNING

Operate the car audio after stopping

the vehicle.

The car audio system should be operated after

having stopped the vehicle in a safe place.

(Operating it while driving a vehicle may lead

to traffic accident.)

Should any of the following abnormal phenom-

ena is observed, immediately stop the use and

operation of the product.

· No sound output.

· Water is spilt on the product.

· A foreign object such as metal or a piece of

paper gets inside the product.

Do not use the product for other purpose

than car use.

This product has been designed for installation and

operation in a vehicle. Do not use it for other pur-

pose.

(Otherwise imperfect installation may cause the

product to drop and cause injury.)

· The product starts smoking.

· Abnormal noise or odor is produced.

(If the use of the product is continued, fire haz-

ard or other accident may result.)

In this case, immediately switch the power off,

check safety and consult your dealer or nearest

KENWOOD service agent or distributor.

Do not use loud volume.

During driving, do not turn the listening vol-

ume too high at which you cannot hear the

sound outside the vehicle.

(You may be unable to notice what is happen-

ing outside the vehicle, and a traffic accident

may result. )

Do not continue sound output at an

abnormal level.

Do not use the speakers for a long period at a

high volume level at which the sound is dis-

torted.

(The system may be overheated and fire haz-

ard may result. )

Do not open the back and top covers of

the product or modify it.

(This may lead to fire hazard or other acci-

dent.)

· For the inspection and servicing, consult your

dealer or nearest KENWOOD service agent or

distributor.

· Servicing by the user may lead to fire hazard

and other accidents.

These indicate what must not be done.

(Inhibition marks)

This indicates what must be done.

(Imperative mark)

· Please install depending to this instruction manual. Please keep it carefully after fin-

ishing reading this. It is better to keep this manual together with the owner's manual

of your vehicle.

· For inquiries on installation, please consult your dealer or nearest service agent.

· Refer to guidance on attached sheet for inquiry about the product to our company.

1. When installing in some types of a car, it is necessary to remove the seat belt. It is

necessary to mount the bolt which fixes a seat belt by the specified force. For

inquiries on torque, please consult your dealer or your car shop.

2. When installing in some types of a car, you have to install using an installation kit.

For inquiries, please consult your dealer.

3. Depending on the year or grade of a car, some vehicles may have changed parts.

For inquiries, please consult your dealer.

Caution

Connection example 4

If the tweeter level is too high.

Tweeter connection from woofer. (Tweeter is installed on the door panel.)

Connection example 3

If the tweeter level is too high.

Tweeter connection from center unit. (Tweeter is installed on the dashboard.)

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Tweeter

Woofer

Speaker output

~Connection cord

(for woofer)

6Connection cord (for tweeter)

Black/Gray

Black

Red

Black

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Black/Gray

Black

7Sound Level Adjuster

(for tweeter)

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Woofer

~Connection cord (for woofer)

6Connection cord which is cut

(for tweeter)

Refer to "Connection exsample 2".

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Connection cord

of vehicle

Black/Gray

Black

Red

Tweeter

Black/Gray

Black

Black/Gray

Black

7Sound Level Adjuster

(for tweeter)

Caution

· The terminal which is not used should be protected by electrical tape for shorting accident prevention.

· Be careful of the polarity of plus/minus and connect depending to the connection example.

"The power to twist something" is called "torque."

Two persons grip each end of one bat, and twist in opposite direction, respectively. In this case, the person with the

thick bat side is more advantageous.

Thus, even if using the same force, turning something with a large radius will have larger twisting strength, or torque.

[Bolting torque of a screw] ; The power in which an adult tightens a

screw normally using an ordinary screwdriver is 1-2N·m (0.1-0.2kgf·m).

[Bolting torque of a bolt] ; The torque when tightening a bolt by 25kg

power using a wrench is 49N·m (5kgf·m).

About bolting torque

10kg

1kg

0.1m

Both are the same torque, 9.8N·m (1kgf·m).

Connection example 2

Tweeter connection from woofer. (Tweeter is installed on the door panel.)

System connections

Connection example 1

Tweeter connection from center unit. (Tweeter is installed on the dashboard.)

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Tweeter

Woofer

Speaker output

~Connection cord

(for woofer)

6Connection cord (for tweeter)

Black/Gray

Black

Red

Black

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Woofer

~Connection cord (for woofer)

6Connection cord which is cut

(for tweeter)

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Connection cord

of vehicle

6Connection cord (for tweeter)

Black/Gray

Black

Red

Cut

Tweeter

Black/Gray

Black

The high path filter for a tweeter is built in the main part of a tweeter.

CAUTION

WARNING

Immediately stop operation in case of abnormality.

Thank you for purchasing this product.

Please read this instruction manual thoroughly before installing speakers, and

install speakers correctly.

Tools required for installation Phillips screwdriver, Flat-head screwdriver, Clip driver, Pliers, Nippers, Wrench,

Electric hand drill and bits, Cutting knife, Electrical tape, Scissors, Felt-tip pen

Safety caution

Be sure to observe the warning and caution provided below as they are critical for your safety.

The meanings of the symbols are as follows.

SEPARATE CUSTOM FIT SPEAKER

K-ES01

INSTRUCTION MANUAL

KENWOOD CORPORATION

B54-1210-20 (FHP)

Installation cautions

If the product is handled erroneously by ignoring the instruction of this mark,

fatal hazard or serious injury on human body may result.

If the product is handled erroneously

by ignoring the instruction of this

mark, injury on human body, or dam-

age of product may result.

CAUTION

Work depending to instruction manual.

When installing or wiring the product,

be sure to follow strictly the instruction

and installation manuals of the product.

(If the instructions are not observed

strictly, the product may be displaced

and hit you during braking and there

may also be a risk of electric shock or

fire hazard.)

Please read thoroughly.

Be careful not to damage the tank and

electric wiring.

In case the product is installed by mak-

ing holes on the vehicle chassis, be

careful never to damage the gasoline

tank, piping, electric wiring or other

parts of the vehicle.

(Otherwise fire hazard may result.)

Do not pull the cord.

When you remove the connector, please

remove and lock it with the connector

main part, without pulling the cord.

Otherwise disconnection of a cord and

poor contact may result.

Do not cut insulation tube in the middle

of a power cord.

Do not use power cord for other prod-

ucts by cutting insulation tube in the

middle of a power cord.

(Otherwise a shorting accident* may

occur, which could result in fire acci-

dent.)

Do not open the back and top covers of

the product or modify it.

(This may lead to fire hazard or other

accident.)

· For inspection and servicing, consult

your dealer or nearest KENWOOD ser-

vice agent or distributor.

· Servicing by the user may lead to fire

hazard or other accidents.

Use a fuse with the specified rating.

When the fuse is blown, first ensure that

there is no short-circuiting* between the

wired cords, then replace with a new

fuse with the capacity (Ampere value)

specified on the fuse box.

(Using other fuse than specified may

lead to fire hazard.)

· For fuse replacement, refer to the

owner's manual of your vehicle.

Please check the spec.

Use provided parts for installation.

Be sure to install a product using pro-

vided parts. When parts other than the

provided ones are used, a product may

fall off and hit the passenger while driv-

ing, causing injury or product breakage.

Inspect the vehicle after installation.

After installation of the product, be sure

to check that the brake lamps, head

lamps, direction indicators, windshield

wipers, power window, etc. of the vehi-

cle function normally.

(If any of the vehicle functions are dam-

aged due to incorrect wiring , etc., traf-

fic accident may result. )

Remove battery connection before work.

Before installing or wiring anything, be

sure to remove the cable from the nega-

tive terminal of the battery.

(Otherwise a shorting accident* may

occur, which could result in fire acci-

dent.)

Remove negative terminal.

Use proper tools for the processing

objects.

When tightening a bolt or nut, always be

sure to use the tool matching its size. If

the securing torque of a part is speci-

fied, be sure to secure it with the speci-

fied force.

(Otherwise the bolt or nut may be dam-

aged or detached during use.)

Wrap cords with protective tape.

The cords near metallic parts of the

vehicle should be protected against

sharp edge of the metallic parts by

wrapping insulating tape around them.

(If a cord is damaged, electric shock or

short-circuiting* as well as fire hazard

may result.)

* Short-circuiting and shorting accident

Short-circuiting refers to the direct connection between the positive and negative poles of electricity. This may occur when a stripped cord (electric wiring) comes in

contact with another cord or metallic part of vehicle. Short-circuiting may produce spark, which may be caught by surrounding objects and result in fire hazard.

Cautions on use

WARNING

Operate the car audio after stopping

the vehicle.

The car audio system should be operated after

having stopped the vehicle in a safe place.

(Operating it while driving a vehicle may lead

to traffic accident.)

Should any of the following abnormal phenom-

ena is observed, immediately stop the use and

operation of the product.

· No sound output.

· Water is spilt on the product.

· A foreign object such as metal or a piece of

paper gets inside the product.

Do not use the product for other purpose

than car use.

This product has been designed for installation and

operation in a vehicle. Do not use it for other pur-

pose.

(Otherwise imperfect installation may cause the

product to drop and cause injury.)

· The product starts smoking.

· Abnormal noise or odor is produced.

(If the use of the product is continued, fire haz-

ard or other accident may result.)

In this case, immediately switch the power off,

check safety and consult your dealer or nearest

KENWOOD service agent or distributor.

Do not use loud volume.

During driving, do not turn the listening vol-

ume too high at which you cannot hear the

sound outside the vehicle.

(You may be unable to notice what is happen-

ing outside the vehicle, and a traffic accident

may result. )

Do not continue sound output at an

abnormal level.

Do not use the speakers for a long period at a

high volume level at which the sound is dis-

torted.

(The system may be overheated and fire haz-

ard may result. )

Do not open the back and top covers of

the product or modify it.

(This may lead to fire hazard or other acci-

dent.)

· For the inspection and servicing, consult your

dealer or nearest KENWOOD service agent or

distributor.

· Servicing by the user may lead to fire hazard

and other accidents.

These indicate what must not be done.

(Inhibition marks)

This indicates what must be done.

(Imperative mark)

· Please install depending to this instruction manual. Please keep it carefully after fin-

ishing reading this. It is better to keep this manual together with the owner's manual

of your vehicle.

· For inquiries on installation, please consult your dealer or nearest service agent.

· Refer to guidance on attached sheet for inquiry about the product to our company.

1. When installing in some types of a car, it is necessary to remove the seat belt. It is

necessary to mount the bolt which fixes a seat belt by the specified force. For

inquiries on torque, please consult your dealer or your car shop.

2. When installing in some types of a car, you have to install using an installation kit.

For inquiries, please consult your dealer.

3. Depending on the year or grade of a car, some vehicles may have changed parts.

For inquiries, please consult your dealer.

Caution

Connection example 4

If the tweeter level is too high.

Tweeter connection from woofer. (Tweeter is installed on the door panel.)

Connection example 3

If the tweeter level is too high.

Tweeter connection from center unit. (Tweeter is installed on the dashboard.)

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Tweeter

Woofer

Speaker output

~Connection cord

(for woofer)

6Connection cord (for tweeter)

Black/Gray

Black

Red

Black

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Black/Gray

Black

7Sound Level Adjuster

(for tweeter)

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Woofer

~Connection cord (for woofer)

6Connection cord which is cut

(for tweeter)

Refer to "Connection exsample 2".

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Connection cord

of vehicle

Black/Gray

Black

Red

Tweeter

Black/Gray

Black

Black/Gray

Black

7Sound Level Adjuster

(for tweeter)

Caution

· The terminal which is not used should be protected by electrical tape for shorting accident prevention.

· Be careful of the polarity of plus/minus and connect depending to the connection example.

"The power to twist something" is called "torque."

Two persons grip each end of one bat, and twist in opposite direction, respectively. In this case, the person with the

thick bat side is more advantageous.

Thus, even if using the same force, turning something with a large radius will have larger twisting strength, or torque.

[Bolting torque of a screw] ; The power in which an adult tightens a

screw normally using an ordinary screwdriver is 1-2N·m (0.1-0.2kgf·m).

[Bolting torque of a bolt] ; The torque when tightening a bolt by 25kg

power using a wrench is 49N·m (5kgf·m).

About bolting torque

10kg

1kg

0.1m

Both are the same torque, 9.8N·m (1kgf·m).

Connection example 2

Tweeter connection from woofer. (Tweeter is installed on the door panel.)

System connections

Connection example 1

Tweeter connection from center unit. (Tweeter is installed on the dashboard.)

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Tweeter

Woofer

Speaker output

~Connection cord

(for woofer)

6Connection cord (for tweeter)

Black/Gray

Black

Red

Black

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Center unit

8Erectro-tap (for woofer)

Refer to "Woofer connections" in this instruction manual.

Woofer

~Connection cord (for woofer)

6Connection cord which is cut

(for tweeter)

Black/Gray

Black

Black/Gray

Black

Vehicle connector

Connection cord

of vehicle

6Connection cord (for tweeter)

Black/Gray

Black

Red

Cut

Tweeter

Black/Gray

Black

The high path filter for a tweeter is built in the main part of a tweeter.

CAUTION

WARNING

Immediately stop operation in case of abnormality.

PEAK POWER

160W

Upgrade Speaker

SEPARATE CUSTOM FIT SPEAKER

K-ES01 INSTRUCTION MANUAL

· Installation

example C

· Installation

example D

Depending on vehicle type, you may install

using -Attachment.

Tapping screw

· · · · ·

× 8

(

6×20mm)

Tapping screw

· · · · ·

× 8

(

5×20mm)

Tapping screw

· · · · ·

× 8

(

4×20mm)

Machine screw

· · · · ·

× 8

(M4

×12mm)

Self-tapping screw

· ·

× 6

(

6×20mm)

Washer

· · · · · · · · · ·

× 8

(

Washer

· · · · · · · · · ·

× 8

(

Erectro-tap · · · · · · ·

× 8

Sealing tape

· · · · · · ·

× 2

(thin)

Sealing tape

· · · · · · ·

× 2

(thick)

Attachment · · · · · · ·

× 8

Spacer (rubber) · · · ·

× 2

Connection cord · · ·

× 2

Parts included (for woofer)

Check that the following parts for the woofer are provided with the product.

Mounting location for woofer

Refer to "Woofer connections" for the connection of vehicle connector and ~Connection cord.

· Installation

example A

· Installation

example B

Vehicle connector

Connect by using

~Connection cord and

8Electro-tap

6 or 7Washer

Factory or

provided screw

Vehicle connector

Connect by using

~Connection cord and

8Electro-tap

6 or 7Washer

-Attachment

Factory or

provided screw

Vehicle connector

Connect by using

~Connection cord and

8Electro-tap

5Tapping screw

Vehicle

connecto

Connect by using

~Connection cord and

8Electro-tap

6 or 7Washer

=Spacer

Factory or

provided screw

Face "side A" to

speaker side and install it.

Depending on vehicle type, you may install

using 5Tapping screw. (When the factory

speaker is being fixed by rivets, the rivets

must be cut.)

Depending on vehicle type, you may install

using 6 or 7Washer.

Depending on vehicle type, you may install

using =Spacer. (Face "side A" to speaker

side and install it.)

Installation preparation

Stick 9 and 0Sealing tape, in order to prevent vibration and leak.

0Sealing tape (thick)

Stick 0Sealing tape after fixing the speaker by screws.

9Sealing tape (thin)

· Stick 9 and 0Sealing tape

Be sure to install prod-

uct using provided seal-

ing tape. Installing with-

out using sealing tape

may cause water leak

into a vehicle.

Installation for tweeter

Before work

· Before making holes, check the mounting space with the supplied template (in the inner flap of the carton box).

· To prevent noise pick-up, keep the wiring of this unit away from motors, high voltage leads and other possible

noise sources.

· To prevent short-circuiting, keep all wiring away from moving parts, sharp edges, cut metal, etc.

· Do not switch power ON until wiring is completed.

Installation procedure

1. Select the mounting position, referring to "Mounting location for tweeter".

2. Place the supplied template on the selected position and mark the hole positions with a felt-tip pen.

3. Cut out a hole for letting the cord pass, and make screw holes in the position of the mark.

4. Install 4Mounting bracket using 1 or 2Tapping screw, 3Speed nut and 5Double-faced tape.

5. Join the projections of 4Mounting bracket to the holes at the bottom of a tweeter.

Installation

Caution

· Install the tweeter so that it will not come in contact with the window glass etc.

· When you check the mounting space, check that there is no contact by opening and closing of a door, or

no interference with safeguards, such as an air bag.

· Be careful not to damage the tank and hose, in the case of processing work.

· Do not install the tweeters in locations which may be subject to water or hot air.

· Fix the tweeter in a position which does not hinder the driving operations.

· Do not use any parts other than specified. (Otherwise imperfect installation may cause the tweeter instal-

lation to loosen, and cause it to drop.)

Caution

· Do not adjust to an impossible angle.

· Do not hold front side or cord of the tweeter when adjusting.

· The tweeter adjustment should be operated after having stopped the vehicle at a safe place.

Parts included (for tweeter)

Check that the following parts for the tweeter are provided with the product.

Mounting location for tweeter

1. On the dashboard

2. On the door panel

It may be unable to mount on the door

of some vehicle types.

;;;

;;

;;;

;

;;;;

;;;

Tapping screw

· · · · ·

× 4

(

3×10mm)

Tapping screw

· · · · ·

× 4

(

3×16mm)

Speed nut

· · · · · · · ·

× 4

(

Mounting bracket · ·

× 2

Double-faced

· · · · · ·

× 2

tape

Connection cord · · ·

× 2

Sound Level

· · · · · ·

× 2

Adjuster

1. Select the mounting

position.

2. Make holes.

3. Mount tweeter.

;;;

;

;;

;

;;

;;;

;

;;

Tweeter

1 or

2Tapping screw

4Mounting

bracket

5Double-faced

tape

3Speed nut

Angle adjustment

· After installation, you can adjust direction of this tweeter to an optimum angle for better music

reproduction. As shown in figure, hold the side of the tweeter, change direction of the tweeter slow-

ly, and decide the direction with the best balance of L and R.

Frequent direction adjustment and impossible adjustment may not maintain direction of the

tweeter.

Warning

· When a vehicle has been left under direct sunlight, the surface temperature of the tweeter may rise to a

considerable level. Keep in mind that there is danger of a burn if it is touched.

Decrease enough the internal temperature of a vehicle before adjusting.

;;;

;;;;

;;;;;

;;;;

;;;

;

;;;;

Hold the side.

Please face the tweeter on the side of the driver's seat towards

the direction of the passenger seat, and face the tweeter on the

side of the passenger seat towards the driver's seat side.

Set the arrow of the template in the direction of sound.

Removal of rivet

· When the factory speaker is being fixed by rivets.

A rivet is removed by making a hole in the lock

portion (the central portion) of it with a drill.

Also remove the fragment of the rivet.

The removed rivet cannot be re-used.

Woofer connections

· Connection of vehicle connector and ~Connection cord

Connect using 8Electro-tap.

· Connection to woofer terminal

1. Remove insulation cover of cord.

2. Loosen the cap of terminal and pass cord through the hole.

3. Close the cap of terminal tightly.

Rivet which is fixing

the factory speaker

Caution

· If the metal part of a door is deformed, the diameter of

the screw hole becomes large and it becomes impossi-

ble to install the woofer.

Pull

Loosen

side : Red line

side : Black line

Tighten

To woofer

terminal

~Connection cord

8Electro-tap

Vehicle connector

Connection cord of vehicle

Connection cord

Clamp using pliers.

How to use the electro-tap

Make each polarity (

)

match and connect.

Caution

· Connect so that the tip of the connection cord does not

contact metal portions other than terminal.

· Tighten firmly so that the connection cord does not

come off, while driving vehicle.

About polarity (

)

Connecting with the wrong speaker polarity will not

reproduce with the right sound stage. Be careful of the

polarity and connect properly.

Caution

· The terminal which is not used should be protected by

electrical tape for shorting accident prevention.

Join the projections of 4Mounting bracket to these holes.

Tweeter bottom

Reviews

There are no reviews of this manual yet.

Related Products

Cover page of KENWOOD SRC603 Owner's Manual

KENWOOD K-ES01 Owner's Manual

Manual details

We guarantee that...

Sample pages

Reviews

Related Products

KENWOOD SRC603 Owner's Manual

KENWOOD TRC-60 Service Manual

KENWOOD KSW6200 Service Manual

KENWOOD RDT-131 Owner's Manual

KENWOOD DP-2020 Owner's Manual

Popular Brands

General

Members Area