3
KGP-2A/2B
TK-760G/762G/860G/862G/768G/868G Series
(TK-*60G Series)
s Installing the KCT-35 in the Transceiver
1. Remove the upper cover from the transceiver.
2. Lift the DC cord bushing ( 1 ) from the chassis.
3. Remove the pad as shown in the Figure 3 ( 2 ).
4. Insert the KCT-35 cable ( 3 ) into the chassis ( 4 ). The
wire harness band ( 5 ) must be inside the chassis.
5. Replace the DC cord bushing ( 6 ).
6. Connect the KCT-35 to the TX-RX unit (A/2) as shown in
Figure 4 ( 7 ).
Fig. 3
1
2
Fig. 4
A
B
C
3
4
6
7
5
KGP-2A/2B or
through KCT-36
extension cable.
KCT-35
1
13
15
3
CN5
A
B
C
CN4
CN3
Connector
Wire Color
Pin No.
A-1
Brown
4
A-2
Green
7
A-3
NC
A-4
Orange
5
A-5
NC
A-6
NC
A-7
Yellow
6
A-8
Blue
8
Connector
Wire Color
Pin No.
B-1
Gray
10
B-2
White
11
B-3
Purple
9
C-1
NC
C-2
Black
3
C-3
Red
1
INSTALLATION / REALIGNMENT
REALIGNMENT
Transceiver Setting
When the KGP-2A/2B is connected to a transceiver, the
transceiver functions must be set. The transceiver FPU is
used to make this setting.
For a connection method, see Figure 1.
s TK-*80 Series Setting Method
1. Setting with KPG-49D (K and M markets FPU)
1) Select "Optional Features" from "Edit" on the menu bar
and change Com2 (Internal Port) from "[None]" to "[AUX
Hook/PTT]".
2. Setting with KPG-60D (E markets FPU)
1) Select "Extended Function" from "Edit" on the menu
bar and change Com2 from "[None]" to "[AUX Hook/
PTT]".
s TK-*60G Series Setting Method
Use the KPG-56D as the FPU.
1) Select "Key assignment" from "Edit" on the menu bar,
and set "Foot Switch" to "[None]".
2) Select "Optional Features" from "Edit" on the menu bar
and change "ACC Hook/DTC" from "[ACC Hook]" to
"[DTC]".
Note :
Applicable only for S/No. 302XXXXX or later.
KGP-2A/2B Setting
After programming the transceiver, you need to config-
ure the KGP-2A/2B. Using the FPU (KPG-73D), you can con-
figure the KGP-2A/2B .
Using a cross-wired serial cable (KGP-2A/2B side : D-sub
9- pin female) as shown in Figure 2, plug one connector into
the RS-232C (COM) port of your PC and the other end to the
ACC1 connector on the rear panel of the KGP-2A/2B.
s KGP-2A/2B Setting Method
1) Create a data file using the FPU (KPG-73D).
2) After configuring the KGP-2A/2B to the Programming
Menu mode, upload the data file to the KGP-2A/2B.
For detailed instructions, refer to the Help file included in
the FPU.
To set the KGP-2A/2B in the Programming Menu mode,
refer to "Start the Programming Menu mode" on page 6.
