3
Important safeguards
1.
Read Instructions All the safety and operating instructions should be
read before the appliance is operated.
2.
Retain Instructions The safety and operating instructions should be
retained for future reference.
3.
Heed Warnings All warnings on the appliance and in the operating
instructions should be adhered to.
4.
Follow Instructions All operating and use instructions should be fol-
lowed.
5.
Water and Moisture The appliance should not be used near water
for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, and the like.
6.
Carts and Stands The appliance should be used only with a cart or
stand that is recommended by the manufacturer.
7.
Wall or Ceiling Mounting The appliance should be mounted to a
wall or ceiling only as recommended by the manufacturer.
8.
Ventilation The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface that
may block the ventilation openings; or if placed in a built-in installation,
such as a book case or cabinet that may impede the flow of air through the
ventilation openings, there should be free space of at least 20 cm and open
up behind the appliance.
9.
Heat The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers)
that produce heat.
10.
Power Sources The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on the
appliance.
11.
Polarization If the appliance is provided with a polarized plug having
one blade wider than the other, please read the following information: The
polarization of the plug is a safety feature. The polarized plug will only fit
the outlet one way. If the plug does not fit fully into the outlet, try revers-
ing it. If there is still trouble inserting it, the user should seek the services
of a qualified electrician. Under no circumstances should the user attempt
to defeat the polarization of the plug.
12.
Power-Cord Protection Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, especially near plugs, convenience receptacles, and the point
where they exit from the appliance.
13.
Cleaning The appliance should be cleaned only as recommended by
the manufacturer.
14.
Power Lines An outdoor antenna should be located away from power
lines.
15.
Nonuse Periods The power cord of the appliance should be unplugged
from the outlet when left unused for a long period of time.
16.
Object and Liquid Entry Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through openings.
17.
Damage Requiring Service The appliance should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
6A. An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
PORTABLE CART WARNING
S3125A
18.
Servicing The user should not attempt to service the appliance beyond
that described in the operating instructions. All other servicing should be
referred to qualified service personnel.
19.
Outdoor Antenna Grounding If an outside antenna is connected to
the receiver, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides information with
regard to proper grounding of the mast and supporting structure, ground-
ing of the lead-in wire to an antenna discharge unit, size of grounding con-
ductors, location of the antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode. See Figure 73.1.
FIGURE 73.1:
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELEC-
TRICAL CODE
Precautions
1. Warranty Claim
You can find the serial number of the rear panel. In case of warranty
claim, please report this number.
2. Care
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a
weak solution of mild detergent and water, wring it out dry, and wipe
off the dirt. Following this, dry immediately with a clean cloth. Do not
use rough material, thinners, alcohol or other chemical solvents or
cloths since these could damage the finish or remove the panel letter-
ing.
3. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
q
Some models are designed for use only with the power supply
voltage of the region where they are sold.
U.S.A. and Canadian models:
AC 120 V, 60 Hz
European model:
AC 230 V, 50 Hz
Worldwide model:
AC 120 V/220 230 V switchable,
50/60 Hz
q
Voltage Selector (Rear Panel)
Worldwide models are equipped with a voltage selector to con-
form with local power supplies. Be sure to set this switch to match
the voltage of the power supply in your area before turning the
power button on. (See "Setting the voltage selector and Tuning
step frequency (Worldwide models only)", P. 4.) Models without a
voltage selector can only be used in areas where the power supply
is the same as that of the unit.
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUND CLAMPS
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ANTENNA
LEAD IN
WIRE
NEC NATIONAL ELECTRICAL CODE
S2898A
