3
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use. Unplug this
Plasma Monitor from AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Clean
only with dry cloth.
Follow all warnings and instructions marked on the
Plasma
Monitor.
For added protection to the
Plasma Monitor during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and power line surges.
Do not expose this Plasma Monitor to rain or use near water...
for example, in a wet basement, near a swimming pool, etc...
The Plasma Monitor shall not be exposed to dripping or
splashing. No objects filled with liquids, such as vases, shall
be placed on the Plasma Monitor.
Only use attachments/accessories specified by the
manufacturer.
Do not place this
Plasma Monitor on an unstable cart, stand,
or table. The
Plasma Monitor may fall, causing serious injury
to a child or adult, and serious damage to the
Plasma
Monitor. Use only with a cart or stand recommended by the
manufacturer, or sold with the
Plasma Monitor.
CAUTION:
This
Plasma Monitor for use only with following Stand and
Mount Unit. Use with other stands or mount units is capable of
resulting in instability causing possible injury.
SANYO Table top stand
KA-TD-H10S
SANYO Tilt mount unit
KA-TI-H10
SANYO Wall mount unit
KA-WA-H10WV
SANYO Ceiling mount unit
KA-CH-H10
SANYO Floor Stand
KA-TD-42HW
An appliance and cart combination should
be moved with care.
Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and top of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions. Do not install near any
heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
This
Plasma Monitor should not be placed in a built-in
installation such as a book case unless proper ventilation is
provided.
Never push objects of any kind into this
Plasma Monitor
through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the
Plasma Monitor.
This
Plasma Monitor should be operated only from the type
of power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Protect the power cord from being walked on
or pinched particularly at plugs. convenience receptacles, and
the point where they exit from the apparatus.
Do not attempt to service this
Plasma Monitor yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
Unplug this
Plasma Monitor from wall outlet and refer
servicing to qualified service personnel under the following
conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the
Plasma Monitor.
c. If the
Plasma Monitor has been exposed to rain or water.
d. If the
Plasma Monitor does not operate normally by
following the operating instructions. Adjust only those
controls that are covered by the operating instructions as
improper adjustment of other controls may result in damage
and will often require extensive work by a qualified
technician to restore the
Plasma Monitor to normal
operation.
e. If the
Plasma Monitor has been dropped or the cabinet
has been damaged.
f. When the
Plasma Monitor exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this
Plasma
Monitor, ask the service technician to perform routine safety
checks to determine that the
Plasma Monitor is in safe
operating condition.
AC Power Cord has a grounding-type
AC line plug. This is a safety feature to
be sure that the plug will fit into the
power outlet. Do not try to defeat this
safety feature. Should you be unable to
insert the plug into the outlet, contact
your electrician.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
GROUND
