PIONEER PDP-S25-LR/XIN1/E Owner's Manual

Cover page of PIONEER PDP-S25-LR/XIN1/E Owner's Manual

Owner's Manual for PIONEER PDP-S25-LR/XIN1/E, downloadable as a PDF file.

We also have service manual to this model.

Manual details

  • Immediate download after payment.
  • Delivered as a PDF file.
  • The manual has 38 pages
  • File size: 4.01 MB
  • Available language versions: French, English, Spanish, Dutch, German, Chinese Traditional, Italian
  • Different language versions may vary sligthly in file size and page count.

We guarantee that...

  • our manuals are complete,
  • our manuals are checked with antivirus,
  • We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

Thumbnail of page 1Thumbnail of page 2Thumbnail of page 3Thumbnail of page 4
Thumbnail of page 5Thumbnail of page 6Thumbnail of page 7Thumbnail of page 8
Thumbnail of page 9
background image
PDP-S25-LR
PDP-S26-LR
Operating Instructions
Mode d'emploi
Bedienungsanleitung
Istruzioni per l'uso
Gebruiksaanwijzing
Manual de instrucciones
Speaker System
Enceintes acoustiques
Lautsprechersystem
Sistema di diffusori
Luidsprekersysteem
Sistema de altavoces
background image
PDP-S25-LR
PDP-S26-LR
Operating Instructions
Mode d'emploi
Bedienungsanleitung
Istruzioni per l'uso
Gebruiksaanwijzing
Manual de instrucciones
Speaker System
Enceintes acoustiques
Lautsprechersystem
Sistema di diffusori
Luidsprekersysteem
Sistema de altavoces
background image
English
2
See the description below for details of the installation.
NOTE:
÷ If you install the speakers flush/air, you cannot use the
buttons on the right side of the display. Please use the
remote control.
CHECKING THE ACCESSORIES
7 Speaker cable x 2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished reading
the instructions, put them away in a safe place for future
reference.
BEFORE USE
÷ The nominal impedance of this speaker system is 8 ohms.
÷ In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
÷ Do not supply power to the speaker system in
excess of the maximum permissable input. This
can result in damage or a possible fire hazard.
÷ When connecting or disconnecting pin-plugs, be
sure that amplifier power is OFF.
÷ When using a graphic equalizer to emphasize loud
sounds of a high frequency range, do not use
excessive amplifier volume.
÷ Do not force a low-powered amplifier to produce a
loud volume of sound (the amplifier's harmonic
distortion will be increased, and you may damage
the speaker).
÷ Please handle the speakers with sufficient care, as
the grille net and the cabinet can become damaged
or broken when they are subjected to strong external
impacts.
÷ Placing a CRT computer screen or CRT monitor near to
the speakers may result in interference or color distortion.
If this happens, distance the monitor from the speakers.
7 Operating Instructions
7 Speaker mounting fittings (Used when installing the
speakers flush with the display)
Bracket for flush mounting (RIGHT) x 2
7 Speaker mounting fittings (used when mounting
the speaker so as to allow angle adjustment)
7 Speakers mounting screws
NOTE:
÷ Always use the accessory mounting fittings for
installation.
÷ When screws other than those enclosed as accessories
are used to install the speakers, the speakers may drop
off or accidents may be caused. Always use the screws
enclosed as accessories.
Notes on Installation Work:
This product is marketed assuming that it is installed by
qualified personnel with enough skill and competence.
Always have an installation specialist or your dealer install
and set up the product.
PIONEER cannot assume liabilities for damage caused
by mistake in installation or mounting, misuse,
modification or a natural disaster.
x 12
Speakers are designed to allow the two methods of
installation shown, in accordance with the user's preference:
1. Flush: Speakers are mounted flat against the sides of
the display, and fixed in position (non-adjustable).
2. Air: Speakers are mounted apart from the sides of the
display, so as to allow adjustment of their angles.
Flush
Air
Bracket for air
mounting (R) x 1
WARNING:
Handling the power cord on this product or cords
associated with accessories sold with the product will
expoes you to lesd, a chemical known to the State of
California and other governmental entities to cause cancer
and birth defects or other reproductive harm.
Wash hands after handling.
Bracket for flush mounting (LEFT) x 2
Bracket for air
mounting (L) x 1
Padding strip x 2
Covers (upper) x 2
Covers (lower) x 2
background image
3
English
English
INSTALLATION ON THE PLASMA
DISPLAY
Flush mount (for fixed-angle installation)
Perform installation according to the following steps 1 to 2.
1 Attach the mounting fittings to the
speakers.
The illustration below shows the right speaker. Attach the left
side mounting fitting in the same way.
1 Attach a bracket (RIGHT) to the top of the right speaker,
as shown.
2 Attach another bracket (RIGHT) to the bottom of the
speaker in the same way.
2 Attach the speakers to the display.
The illustration below shows how to attach of the right speaker.
Attach the left speaker in the same way.
1 Fix the upper screw temporarily in
advance to hang the speaker on the
display (In this case, leave a space
of about 5 mm between the head
of the screw and the display).
5 mm
The display
2
1
2
4
3
INSTALLATION ON THE PLASMA
DISPLAY
Air mount (for adjustable-angle installation)
Perform installation according to the following steps 1 to 2.
1 Attach the mounting fittings to the
speakers.
The illustration below shows the right speaker. Attach the left
side mounting fitting in the same way.
1 Attach the speaker bracket (R) to the right-side speaker.
Remove the locking screw as shown.
2 Attach the top and bottom covers.
The right and left lower speaker
brackets are pre-applied with two-
sided tape to prevent the lower covers
from dropping.
Remove
the
protective paper
from the tape
before fixing the
covers in place.
Locking screw
2 Hang the speaker on the upper screw.
3 Fix the lower screw temporarily.
4 Adjust the position of the speaker and then fix the upper
and lower screws firmly.
CAUTION:
÷ Attach the plasma display to the stand before installing
the speakers. See the Operating Instructions packed to-
gether with the stand for how to assemble the stand.
÷ Do not place force on the speakers' front panel grille net,
or stick your finger or other object into the front of the
speaker, since you may damage the grille net or speaker
unit itself.
÷ When using the "Air" method of
mounting speakers: if the speaker angle
is changed, be sure to lock the speaker
before use, to prevent it from moving.
If the speaker is left in the movable
position, personal injury could results by
pinching fingers in the gap between
speaker and display.
Padding
strip
* Apply the padding strip to
the side of the speaker.
The locking screw is located in the
bottom side of the speaker only.
Protective
paper
background image
English
4
CONNECTION TO A PLASMA
DISPLAY
1 Connecting the speaker cables
1 Switch off the power of the plasma display.
2 Connect the input terminals of the speaker system and
the speaker output terminals of the plasma display with
the accessory speaker cable. Make sure the positive (
ª)
and negative (
·) terminals match when connecting.
1. Push the lever, insert the cable into the hole, and release
the lever.
2. For the output terminals on the plasma display, push the
lever, insert the cable into the hole, and release the lever.
To the
· terminal
To the
ª terminal
(Speaker input terminals of the speaker system)
· terminal (black) ª terminal (red)
Input terminal of speaker
White
White with gray line
ª ··ª
RL
Output terminal of plasma
display
÷ After connection to the terminals, pull lightly on the cable
to confirm that the tips of the cable are properly con-
nected to the terminals. An imperfect connection can
cause sound interruptions and noise.
÷ When cable cores stick out and ª and · lines are short-
circuited, an excessive load will be applied to the plasma
display and the operation will stop or trouble will be
caused.
÷ When the polarity is reversed for one speaker (left or right)
at the time of connection to the plasma display, the bass
reproduction will be reduced, the sound positioning will
be lost, and a correct stereo effect will not be obtained.
2 Attach the speakers to the display.
Theillustrationbelowshows how toattach
ofthe rightspeaker. Attach the left speaker
in the same way.
1 Fix the upper screw temporarily in
advance to hang the speaker on the
display (In this case, leave a space
of about 5 mm between the head
of the screw and the display).
2 Hang the speaker on the upper screw.
3 Fix the lower screw temporarily.
4 Adjust the position of the speaker and then fix the upper
and lower screws firmly.
5 Secure the cable with the cable clip as shown, then press
the remaining speaker cable into the groove (in the lower
cover).
ì Changing the Speaker Angle
1 Remove the upper cover.
2 After pulling up the locking lever, change
the speaker angle as desired, then push
the locking lever down again.
2
4
3
NOTE:
÷ When the display is to be
moved after speaker installa-
tion, do not hold the display by
the speakers. Hold the display
with one hand on the bottom
of the unit and the other on the
handle on the rear. Do not hold
the speakers and raise the
display. This may cause the
deformation or damage of
products.
10
°
10
°
10
°
10
°
10
°
20
°
0
°
5 mm
The display
The speakers can be
adjusted in one of
four angle positions
as desired.
background image
5
English
English
2 How to route cables
Speed clamps are included with the plasma display for
tidying your cables and keeping extra cable length out of the
way.
Flush mount (for fixed-angle installation)
Use the supplied wiring clamp to hide the cables from view.
÷ If you insert the speaker cord too far so that the insulation
is touching the speaker terminal, you may not get any
sound.
< right >
< wrong >
Air mount (for adjustable-angle installation)
Speed clamps
Speaker cable
Speaker cable
Wiring clamp
Speaker cable
Speaker cable
Wiring clamp
Cover
Cover
Cable clip
Cable clip

Reviews

There are no reviews of this manual yet.

Related Products

Cover page of PIONEER DVR-320-S/KCXU Service Manual

This manual has 138 pages, file size: 7.42 MB. It's available in languages: English.

Cover page of PIONEER XV-VS800/DBDXJ Service Manual

This manual has 108 pages, file size: 8.69 MB. It's available in languages: English.

Cover page of PIONEER VSX-AX4AVI-G/FXJ Service Manual

This manual has 274 pages, file size: 20.89 MB. It's available in languages: English.

Cover page of PIONEER X-CX505/GFXJ Owner's Manual

This manual has 60 pages, file size: 2.57 MB. It's available in languages: English, Chinese Simplified.

Cover page of PIONEER VSX-41 Owner's Manual

This manual has 72 pages, file size: 2.58 MB. It's available in languages: English.