PIONEER PDP-S33-LR/XIN1/UC Owner's Manual

PIONEER PDP-S33-LR/XIN1/UC Owner's Manual
0 Rating(s)
Read reviews

Owner's Manual for PIONEER PDP-S33-LR/XIN1/UC, downloadable as a PDF file.

We also have service manual to this model.

Manual details

Immediate download after payment.
Delivered as a PDF file.
The manual has 19 pages
File size: 1.41 MB
Available language versions: French, English, Spanish
Different language versions may vary sligthly in file size and page count.

We guarantee that...

our manuals are complete,
our manuals are checked with antivirus,
We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

PDP-S34-LR

PDP-S33-LR

Operating Instructions

Mode d'emploi

Manual de instrucciones

Speaker System

Enceintes acoustiques

Sistema de altavoces

SRD1281A_En_01_07

05.2.28, 2:49 PM

PDP-S34-LR

PDP-S33-LR

Operating Instructions

Mode d'emploi

Manual de instrucciones

Speaker System

Enceintes acoustiques

Sistema de altavoces

SRD1281A_En_01_07

05.2.28, 2:49 PM

English

CHECKING THE ACCESSORIES

7 Speaker cable x 2

Thank you for buying this Pioneer product.

Please read through these operating instructions before

using your speaker system so you will know how to make

the most of its performance. After you have finished reading

the instructions, put them away in a safe place for future

reference.

BEFORE USE

÷ The nominal impedance of this speaker system is 8 ohms.

÷ In order to prevent damage to the speaker system

resulting from input overload, please observe the

following precautions:

÷ Do not supply power to the speaker system in

excess of the maximum permissable input. This

can result in damage or a possible fire hazard.

÷ When connecting or disconnecting pin-plugs, be

sure that amplifier power is OFF.

÷ When using a graphic equalizer to emphasize loud

sounds of a high frequency range, do not use

excessive amplifier volume.

÷ Do not force a low-powered amplifier to produce a

loud volume of sound (the amplifier's harmonic

distortion will be increased, and you may damage

the speaker).

÷ Please handle the speakers with sufficient care, as

the grille net and the cabinet can become damaged

or broken when they are subjected to strong external

impacts.

÷ Placing a CRT computer screen or CRT monitor near to

the speakers may result in interference or color distortion.

If this happens, distance the monitor from the speakers.

7 Operating Instructions

7 Speaker mounting fittings (Used when installing the

speakers flush with the display)

Bracket for flush mounting (RIGHT) x 2

7 Speaker mounting fittings (Used when installing the

speakers set back with the display)

7 Speakers mounting screws

(M5 x 10mm : Black) x 12

NOTE:

÷ Always use the accessory mounting fittings for

installation.

÷ When screws other than those enclosed as accessories

are used to install the speakers, the speakers may drop

off or accidents may be caused. Always use the screws

enclosed as accessories.

Installation

÷ Consult your dealer if you encounter any difficulties

with this installation.

÷ Pioneer is not liable for any damage resulting from

improper installation, improper use, modification, or

natural disasters.

Bracket for set back mounting (RIGHT) x 2

WARNING:

Handling the power cord on this product or cords

associated with accessories sold with the product will

expose you to lead, a chemical known to the State of

California and other governmental entities to cause cancer

and birth defects or other reproductive harm.

Wash hands after handling.

Bracket for flush mounting (LEFT) x 2

CAUTION:

÷ Attach the Plasma Display to the stand before installing

the speakers. See the Operating Instructions packed to-

gether with the stand for how to assemble the stand.

÷ Do not place force on the speakers' front panel grille net,

or stick your finger or other object into the front of the

speaker, since you may damage the grille net or speaker

unit itself.

Bracket for set back mounting (LEFT) x 2

The customer can select whether to install the speakers flush

with the screen or set back slightly.

Flush

Set back

See the description below for details of the installation.

NOTE:

÷ If you install the speakers flush, you cannot use the

buttons on the right side of the display. Please use the

remote control.

SRD1281A_En_01_07

05.2.28, 2:49 PM

English

INSTALLATION ON THE PLASMA

DISPLAY

Flush mount

Perform installation according to the following steps 1 to 2.

1 Attach the mounting fittings to the

speakers.

The illustration below shows the right speaker. Attach the left

side mounting fitting in the same way.

1 Attach a bracket for flush mounting (RIGHT) to the top of

the right speaker, as shown.

2 Attach another bracket for flush mounting (RIGHT) to the

bottom of the speaker in the same way.

2 Attach the speakers to the display.

The illustration below shows how to attach of the right speaker.

Attach the left speaker in the same way.

1 Fix the upper screw temporarily in

advance to hang the speaker on the

display (In this case, leave a space

of about 5 mm between the head

of the screw and the display).

2 Hang the speaker on the upper screw.

3 Fix the lower screw temporarily.

4 Adjust the position of the speaker and then fix the upper

and lower screws firmly.

5 mm

The display

Padding

strip

Set back mount

Perform installation according to the following steps 1 to 2.

1 Attach the mounting fittings to the

speakers.

The illustration below shows the right speaker. Attach the left

side mounting fitting in the same way.

1 Attach a bracket for set back mounting (RIGHT) to the

top of the right speaker, as shown.

2 Attach another bracket for set back mounting (RIGHT) to

the bottom of the speaker in the same way.

2 Attach the speakers to the display.

The illustration below shows how to attach

of the right speaker. Attach the left speaker

in the same way.

1 Fix the upper screw temporarily in

advance to hang the speaker on the

display (In this case, leave a space

of about 5 mm between the head of

the screw and the display).

2 Hang the speaker on the upper screw.

3 Fix the lower screw temporarily.

4 Adjust the position of the speaker and then fix the upper

and lower screws firmly.

Padding

strip

5 mm

The display

SRD1281A_En_01_07

05.2.28, 2:49 PM

English

CONNECTION TO A PLASMA

DISPLAY

1 Connecting the speaker cables

Before connecting the speaker cables, unplug the Plasma

Display from the power outlet. After you have finished

connecting up, plug the unit back into the power outlet.

Connect the input terminals of the speaker system and

the speaker output terminals of the Plasma Display with

the accessory speaker cables. Make sure the positive (

ª)

and negative (

·) terminals match when connecting.

1. Push the lever, insert the cable into the hole, and release

the lever.

2. For the output terminals on the Plasma Display, push the

lever, insert the cable into the hole, and release the lever.

To the

· terminal

To the

ª terminal

(Speaker input terminals of the speaker system)

· terminal (black) ª terminal (red)

Input terminal of speaker

White

White with gray line

ª ··ª

Output terminal of Plasma

Display

÷ After connection to the terminals, pull lightly on the cable

to confirm that the tips of the cable are properly con-

nected to the terminals. An imperfect connection can

cause sound interruptions and noise.

÷ When cable cores stick out and ª and · lines are short-

circuited, an excessive load will be applied to the Plasma

Display and the operation will stop or trouble will be

caused.

÷ When the polarity is reversed for one speaker (left or right)

at the time of connection to the Plasma Display, the bass

reproduction will be reduced, the sound positioning will

be lost, and a correct stereo effect will not be obtained.

÷ If you insert the speaker cable too far so that the insula-

tion is touching the speaker terminal, you may not get

any sound.

When the display is to be moved after speaker

installation, do not hold the display by the speakers.

Do not hold the speakers and raise the display. This

may cause the deformation or damage of products.

< right >

< wrong >

CAUTION

SRD1281A_En_01_07

05.2.28, 2:50 PM

English

2 How to route cables

Speed clamps and bead bands are supplied for bunching cables. Once properly bunched, follow the steps below to route the

cables.

When the speakers are installed on the sides

The below rear view shows

flush mounting, however cable routing for set back mounting will be the same.

Speaker cable

Speed clamps

Bead band

Attaching speed clamps to the main unit

Attach the speed clamps using any of the 5 holes you prefer

marked with

below, depending on your routing system.

Attaching and removing speed clamps

Insert 1 into an appropriate hole on the rear of the Plasma

Display and snap 2 into the back of 1 to lock the clamp.

Speed clamps are designed to be difficult to undo once in

place. Please attach them carefully.

To remove, use pliers to twist the clamp 90°, pulling

outward. The clamp may deteriorate over time and become

damaged if removed.

Bunching and securing cables with the

bead bands.

Do not allow excessive stress to be placed on the ends of

cables.

SRD1281A_En_01_07

05.2.28, 2:50 PM

Reviews

There are no reviews of this manual yet.

Related Products

PIONEER DEH-P4880MP/XF/BR Owner's Manual

This manual has 51 pages, file size: 0.99 MB. It's available in languages: Portuguese.

PIONEER S-777D Service Manual

This manual has 14 pages, file size: 4.01 MB. It's available in languages: English.

PIONEER FH-P4100R Owner's Manual

This manual has 168 pages, file size: 2.92 MB. It's available in languages: Swedish, French, English, Russian, Greek, Spanish, Dutch, German, Danish, Italian.