PIONEER PDP-S50/XIN/E5 Owner's Manual

Cover page of PIONEER PDP-S50/XIN/E5 Owner's Manual

Owner's Manual for PIONEER PDP-S50/XIN/E5, downloadable as a PDF file.

We also have service manual to this model.

Manual details

  • Immediate download after payment.
  • Delivered as a PDF file.
  • The manual has 14 pages
  • File size: 1.04 MB
  • Available language versions: French, English
  • Different language versions may vary sligthly in file size and page count.

We guarantee that...

  • our manuals are complete,
  • our manuals are checked with antivirus,
  • We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

Thumbnail of page 1Thumbnail of page 2Thumbnail of page 3Thumbnail of page 4
Thumbnail of page 5Thumbnail of page 6Thumbnail of page 7Thumbnail of page 8
Thumbnail of page 9
background image
PDP-S50
Operating Instructions
Mode d'emploi
Speaker System
Enceintes acoustiques
background image
PDP-S50
Operating Instructions
Mode d'emploi
Speaker System
Enceintes acoustiques
background image
English
2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished
reading the instructions, put them away in a safe place for
future reference.
WARNING: Handling the power cord on this product or
cords associated with accessories sold with the product
will expose you to lead, a chemical known to the State
of California and other governmental entities to cause
cancer and birth defects or other reproductive harm.
Wash hands after handling.
CAUTION
About compatibility
This product is designed exclusively for use with the
Pioneer Plasma Display. For more information on
compatibility, please consult with your nearest Pioneer
authorized dealer or service center.
About installation and setting
÷ Attach the Plasma Display to the stand before installing
the speakers. See the Operating Instructions packed
together with the stand for how to assemble the stand.
÷ Do not lift up the display by the speakers. A speaker
may come off, so carry the display by holding it by the
bottom and its handle.
÷ When installing the speaker, do not use any screws
other than those supplied, otherwise the speaker may
come off from the main unit and fall over.
÷ When installing the speaker, tighten the screws firmly.
÷ Please handle the speaker with sufficient care, as the
grille net and the cabinet can become damaged or
broken when they are subjected to strong external
impacts.
÷ Placing a CRT computer screen or CRT monitor near to
the speaker may result in interference or color
distortion. If this happens, distance the monitor from
the speaker.
About the input
÷ In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
÷ Do not use the speaker with anything other than the
specified Pioneer Plasma Display. Doing so may result
in damage or fire.
÷ Be sure to turn the connected devices off and remove
the power cord from the wall outlet beforehand when
changing the connection or installation method.
÷ When using a tone control function to greatly
emphasize treble sounds, do not use excessive
amplifier volume.
Installation
÷ Consult your dealer if you encounter any difficulties
with this installation.
÷ Pioneer is not liable for any damage resulting from
improper installation, improper use, modification, or
natural disasters.
CHECKING THE ACCESSORIES
7 Speaker Cable × 2
7 Speakers Mounting Screw (M5 × 10 mm: Black) × 16
7 Speaker Mounting Bracket
For LEFT-TOP
For LEFT-BOTTOM
For RIGHT-TOP
For RIGHT-BOTTOM
7 Padding Strip × 2
(For Flush mounting)
When speakers are mounted Flush, they are affixed to
the side of the speaker as a buffer.
7 Operating Instructions × 1
There are two ways to mount these speakers,
either Air mount or Flush mount.
7 Air mount
There is a gap of air of about 15 mm between the
speakers and the display.
Speakers
7 Flush mount
The speakers are direct against the display.
Speakers
background image
3
English
English
Flush mounting
Place the speaker so its terminals (bottom)
are facing you.
MOUNTING THE SPEAKERS
TO YOUR PLASMA DISPLAY
Warning
÷ If you wish to change from Flush mounting to Air
mounting or vice versa:
Remove the speaker mounting brackets from the
speakers and the display and remount them from the
beginning.
1. Attaching the Speaker Mounting
Brackets to the Speakers
The left and right speakers themselves are identical,
but become left and right speakers by attaching the
left and right speaker mounting brackets.
There are top and bottom speaker mounting brackets
for both the left and the right speaker. Attach the
appropriate bracket to the top and the bottom on the
back of the speakers with the enclosed screws. (See
Diagram)
The diagram depicts the mounting of the right
speaker. The left speaker mounts in the same way.
There are two types of screw holes on the speaker
mounting brackets as shown in the diagram below. Select
the appropriate holes depending on how you are to mount
the speakers.
Air mounting
Place the speaker so its terminals (bottom)
are facing you.
Speaker Mounting Brackets
(For RIGHT-BOTTOM)
Screw Holes for
Flush mounting
Screw Holes for
Flush mounting
Speaker Mounting
Brackets
(For RIGHT-TOP)
Speaker Mounting Brackets
(For RIGHT- BOTTOM)
Screw Holes for Air mounting
Screw Holes for Air mounting
Speaker Mounting
Brackets
(For RIGHT-TOP)
Screw Holes for
Flush mounting
(2 on inside)
Screw Holes for Air mounting
(2 on outside)
Screw Holes for Air mounting
(2 on outside)
Speaker Mounting Brackets
(For RIGHT-TOP)
(The skinny slot is used for
mounting to the top.)
Screw Holes for
Flush mounting
(2 on inside)
Speaker Mounting Brackets
(For RIGHT- BOTTOM)
background image
English
4
2. If mounting the speakers Flush, affix
the padding strip to the side of the
speakers (side that touches the
display).
Use the enclosed padding strips to buffer the speakers
when mounting them Flush. Peel off the protective
strip and affix to the side of the speakers.
Where to position the padding strip
3. Screw an enclosed screw into the
speaker mounting hole (lower of the
two) at the top, back of the display.
Do not tighten it all the way yet. Leave it loose, with
about 5 mm left to tighten.
4. Hang the speaker mounting bracket
on the screw you installed at the top
by passing the wide part over it and
lowering into the slot; screw in the
lower screw temporarily.
After passing the wide part of the hole of the speaker
mounting bracket (top) over the screw, lower the
speaker onto it.
5. Adjust the position of the speaker
and then fix the upper and lower
screws firmly.
6. Ti ghten the two screws, at the top
and bottom for each speaker (total of
four screws), thus fixing the
speakers to the display.
Padding
Strip
10 mm
The padding
strip should be
attached leaving
a gap of 10 mm
from the top
surface of the
speaker.
Speaker Mounting Hole
Top, Back of
Display
Leave a space of about 5 mm
Top of Display
5 mm
Tighten the bottom
speaker mounting
bracket to the display
temporarily (one place
bottom).
After passing the
wide part of the hole
over the screw,
lower the speaker.
background image
5
English
English
Groove
Speaker Terminal
Speaker Cable
Connecting your Speaker Cables
(to the display)
Connect the cables correctly with respect to the
polarity of the Plasma Display and the speaker
terminals, that is,
ª cable to ª terminals and ·
cable to
· terminals. To do so, connect the cable
with the gray line to the
ª terminals and the white
cable to the
· terminals.
Push the lever, insert the end of the speaker cable
into the hole, and release the lever.
Pay attention to the polarity of the speaker
terminals when making connections. (The gray line
represents the red terminal)
2
1
3
NOTE:
·
Press the lever and insert the end of
the cable.
·
When you release the lever, it clamps
onto the speaker cable.
Caution
·
Be sure to turn the connected devices off and remove
the power cord from the wall outlet beforehand when
changing the connection or installation method.
·
If you insert the speaker cable too far so
that the insulation is touching the speaker
terminal, you may not get any sound.
Please insert it with showing the copper
wire.
Gray line
Gray line
White
Red
Black
Red
Black
·
Red
ª
White
Gray line
Connecting your Speaker Cables
(to the speaker)
CONNECTION TO A PLASMA DISPLAY
· Check if the end of the speaker cables are securely
connected to the terminals by slightly tugging on the
cable after making connections. Loose connections
may result in sound dropouts or noise.
· If there is a short in the
and
cables caused by an
exposed lead wire, excessive load may be applied to
the Plasma Display, resulting in interrupted operation or
malfunction.
· Incorrect connections of the speaker cable to the right
or left of the Plasma Display terminals with respect to
the polarity may result in insufficient stereo sound
effects, delivering poor bass sounds or unstable sound
image.
· Bundle the code without pulling the cord.
CONNECTING THE SPEAKERS
1. Pass the speaker cables through the
hole in the speaker mounting
bracket.
2. Connect the speaker cables to the
speaker.
3. Press the speaker cables into the
groove of the bracket.
4. Connect the speaker cables to the
display.
4

Reviews

There are no reviews of this manual yet.

Related Products

Cover page of PIONEER DEH-3780MP/XF/BR Service Manual

This manual has 72 pages, file size: 4.54 MB. It's available in languages: English.

Cover page of PIONEER PDK-TS26/WL5 Owner's Manual

This manual has 2 pages, file size: 0.48 MB. It's available in languages: French, English, Dutch, German, Italian.

Cover page of PIONEER DRU124X8 Service Manual

This manual has 2 pages, file size: 0.11 MB. It's available in languages: English.

Cover page of PIONEER GM-520T/XU/UC Service Manual

This manual has 29 pages, file size: 2.95 MB. It's available in languages: English.

Cover page of PIONEER DV-266-S/RPWXU Service Manual

This manual has 92 pages, file size: 5.21 MB. It's available in languages: English.