PIONEER PRS-D5000SPL/XH/UC Owner's Manual

PIONEER PRS-D5000SPL/XH/UC Owner's Manual
0 Rating(s)
Read reviews

Owner's Manual for PIONEER PRS-D5000SPL/XH/UC, downloadable as a PDF file.

We also have service manual to this model.

Manual details

Immediate download after payment.
Delivered as a PDF file.
The manual has 8 pages
File size: 1.39 MB
Available language versions: French, English
Different language versions may vary sligthly in file size and page count.

We guarantee that...

our manuals are complete,
our manuals are checked with antivirus,
We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

Thank you for purchasing this PIONEER

product. It is designed to give you many

years of enjoyment.

PIONEER SUGGESTS USING A PRO-

FESSIONAL INSTALLER DUE TO THE

COMPLEXITY OF THIS PRODUCT.

Please read all instructions and WARN-

INGS in this manual before attempting

operation. Should you have any questions,

contact your nearest Pioneer authorized

dealer or installation specialist.

Information to User

Alteration or modifications carried out

without appropriate authorization may

invalidate the user's right to operate the

equipment.

Important

The serial number of this amplifier is writ-

ten on the bottom of the unit. For your

own security and convenience, write it

down on the enclosed warranty card. Keep

the card handy for future reference.

Before Using This Product

After-sales service for Pioneer

products

Please contact the dealer or distributor from where

you purchased the product for its after-sales ser-

vice (including warranty conditions) or any other

information. In case the necessary information is

not available, please contact the companies listed

below:

Please do not ship your product to the companies

at the addresses listed below for repair without

advance contact.

7 U.S.A.

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

7 CANADA

Pioneer Electronics of Canada, Inc.

CUSTOMER SATISFACTION

DEPARTMENT

300 Allstate Parkway

Markham, Ontario L3R OP2

1-877-283-5901

For warranty information please see the Limited

Warranty sheet included with your product.

Selecting fine audio equipment such as the unit you've just purchased is only the start of your

musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your

equipment offers. This manufacturer and the Electronic Industries Association's Consumer

Electronics Group want you to get the most out of your equipment by playing it at a safe level.

One that lets the sound come through loud and clear without annoying blaring or distortion--and,

most importantly, without affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of

sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard against

this by setting your equipment at a safe level BEFORE your hearing adapts.

To establish a safe level:

· Start your volume control at a low setting.

· Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.

Once you have established a comfortable sound level:

· Set the dial and leave it there.

Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all,

we want you listening for a lifetime.

We Want You Listening For A Lifetime

Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since

hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the

Electronic Industries Association's Consumer Electronics Group recommend you avoid prolonged

exposure to excessive noise. This list of sound levels is included for your protection.

Decibel

Level

Example

Quiet library, soft whispers

Living room, refrigerator, bedroom away from traffic

Light traffic, normal conversation, quiet office

Air conditioner at 20 feet, sewing machine

Vacuum cleaner, hair dryer, noisy restaurant

Average city traffic, garbage disposals, alarm clock at two feet.

THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE

Subway, motorcycle, truck traffic, lawn mower

100

Garbage truck, chain saw, pneumatic drill

120

Rock band concert in front of speakers, thunderclap

140

Gunshot blast, jet plane

180

Rocket launching pad

Information courtesy of the Deafness Research Foundation.

Published by Pioneer Corporation.

Publication de Pioneer Corporation.

Tous droits de reproduction et de traduction

réservés.

Printed in U.S.A.

Imprimé aux Etats-Unis

<HRD0240-A> UC

CLASS D MONO AMPLIFIER

AMPLIFICATEUR MONO DE CLASSE D

Owner's Manual

PRS-D5000SPL

Mode d'emploi

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada

TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso

Col.Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

Product registration

Visit us at the following site:

1 Register your product. We will keep the details of

your purchase on file to help you refer to this

information in the event of an insurance claim

such as loss or theft.

2 Receive updates on the latest products and tech-

nologies.

3 Download owner's manuals, order product cata-

logues, research new products, and much more.

About This Product

This product is a class D amplifier for the

subwoofer. If both L (left) and R (right)

channels are connected to the RCA input

of this product, output is mixed because

this product is a mono amplifier.

CAUTION

Never replace the fuse with one of greater

value or rating than the original fuse. Use

of an improper fuse could result in over-

heating and smoke and could cause dam-

age to the product and injury including

burns.

WARNING

· Handling the cord on this product or cords associ-

ated with accessories sold with the product will

expose you to lead, a chemical known to the State

of California and other governmental entities to

cause cancer and birth defects or other reproduc-

tive harm. Wash hands after handling.

· Always use the recommended battery wire and

ground wire, which is sold separately. Connect the

battery wire directly to the car battery positive ter-

minal (+) and the ground wire to the car body.

· Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

· For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

· Check the connections of the power supply and

subwoofer if a fuse for the separately sold battery

wire blows. Detect the cause and solve the prob-

lem, then replace the fuse with another one of the

same size and rating.

· To prevent malfunction of the amplifier and sub-

woofer, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and subwoofer.

Detect the cause and solve the problem.

· Contact the dealer if you cannot detect the cause.

· To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative () terminal of the battery

beforehand.

· Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

· DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

Thank you for purchasing this PIONEER

product. It is designed to give you many

years of enjoyment.

PIONEER SUGGESTS USING A PRO-

FESSIONAL INSTALLER DUE TO THE

COMPLEXITY OF THIS PRODUCT.

Please read all instructions and WARN-

INGS in this manual before attempting

operation. Should you have any questions,

contact your nearest Pioneer authorized

dealer or installation specialist.

Information to User

Alteration or modifications carried out

without appropriate authorization may

invalidate the user's right to operate the

equipment.

Important

The serial number of this amplifier is writ-

ten on the bottom of the unit. For your

own security and convenience, write it

down on the enclosed warranty card. Keep

the card handy for future reference.

Before Using This Product

After-sales service for Pioneer

products

Please contact the dealer or distributor from where

you purchased the product for its after-sales ser-

vice (including warranty conditions) or any other

information. In case the necessary information is

not available, please contact the companies listed

below:

Please do not ship your product to the companies

at the addresses listed below for repair without

advance contact.

7 U.S.A.

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

7 CANADA

Pioneer Electronics of Canada, Inc.

CUSTOMER SATISFACTION

DEPARTMENT

300 Allstate Parkway

Markham, Ontario L3R OP2

1-877-283-5901

For warranty information please see the Limited

Warranty sheet included with your product.

Selecting fine audio equipment such as the unit you've just purchased is only the start of your

musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your

equipment offers. This manufacturer and the Electronic Industries Association's Consumer

Electronics Group want you to get the most out of your equipment by playing it at a safe level.

One that lets the sound come through loud and clear without annoying blaring or distortion--and,

most importantly, without affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of

sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard against

this by setting your equipment at a safe level BEFORE your hearing adapts.

To establish a safe level:

· Start your volume control at a low setting.

· Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.

Once you have established a comfortable sound level:

· Set the dial and leave it there.

Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all,

we want you listening for a lifetime.

We Want You Listening For A Lifetime

Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since

hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the

Electronic Industries Association's Consumer Electronics Group recommend you avoid prolonged

exposure to excessive noise. This list of sound levels is included for your protection.

Decibel

Level

Example

Quiet library, soft whispers

Living room, refrigerator, bedroom away from traffic

Light traffic, normal conversation, quiet office

Air conditioner at 20 feet, sewing machine

Vacuum cleaner, hair dryer, noisy restaurant

Average city traffic, garbage disposals, alarm clock at two feet.

THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE

Subway, motorcycle, truck traffic, lawn mower

100

Garbage truck, chain saw, pneumatic drill

120

Rock band concert in front of speakers, thunderclap

140

Gunshot blast, jet plane

180

Rocket launching pad

Information courtesy of the Deafness Research Foundation.

Published by Pioneer Corporation.

Publication de Pioneer Corporation.

Tous droits de reproduction et de traduction

réservés.

Printed in U.S.A.

Imprimé aux Etats-Unis

<HRD0240-A> UC

CLASS D MONO AMPLIFIER

AMPLIFICATEUR MONO DE CLASSE D

Owner's Manual

PRS-D5000SPL

Mode d'emploi

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada

TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso

Col.Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

Product registration

Visit us at the following site:

1 Register your product. We will keep the details of

your purchase on file to help you refer to this

information in the event of an insurance claim

such as loss or theft.

2 Receive updates on the latest products and tech-

nologies.

3 Download owner's manuals, order product cata-

logues, research new products, and much more.

About This Product

This product is a class D amplifier for the

subwoofer. If both L (left) and R (right)

channels are connected to the RCA input

of this product, output is mixed because

this product is a mono amplifier.

CAUTION

Never replace the fuse with one of greater

value or rating than the original fuse. Use

of an improper fuse could result in over-

heating and smoke and could cause dam-

age to the product and injury including

burns.

WARNING

· Handling the cord on this product or cords associ-

ated with accessories sold with the product will

expose you to lead, a chemical known to the State

of California and other governmental entities to

cause cancer and birth defects or other reproduc-

tive harm. Wash hands after handling.

· Always use the recommended battery wire and

ground wire, which is sold separately. Connect the

battery wire directly to the car battery positive ter-

minal (+) and the ground wire to the car body.

· Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

· For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

· Check the connections of the power supply and

subwoofer if a fuse for the separately sold battery

wire blows. Detect the cause and solve the prob-

lem, then replace the fuse with another one of the

same size and rating.

· To prevent malfunction of the amplifier and sub-

woofer, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and subwoofer.

Detect the cause and solve the problem.

· Contact the dealer if you cannot detect the cause.

· To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative () terminal of the battery

beforehand.

· Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

· DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

CAUTION:

To prevent damage and/or injury

· Do not ground the speaker wire directly or con-

nect a negative () lead wire for several speakers.

· This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck or bus, check the battery

voltage.

· If the car stereo is kept on for a long time while

the engine is at rest or idling, the battery may go

dead. Turn the car stereo off when the engine is at

rest or idling.

· If the system remote control wire of the amplifier

is connected to the power terminal through the

ignition switch (12 V DC), the amplifier will

always be on when the ignition is on-- regardless

of whether the car stereo is on or off. Because of

this, the battery could go dead if the engine is at

rest or idling.

· DO NOT connect a subwoofer with a lower

impedance than specified in the "Connecting the

Unit" section. Amplifier damage, smoke, and

overheating could result from a non-specified con-

nection. The amplifier surface could also become

hot to the touch and minor burns could result.

· Connect either of two subwoofers to the amplifier;

1: a subwoofer with a 750 W or larger nominal

input and an impedance 4

, or 2: a subwoofer

with a 1,500 W or larger nominal input and an

impedance 2

. If the nominal input and imped-

ance are out of the above ranges, the subwoofer

may catch fire, emit smoke or become damaged.

· Install and route the separately sold battery wire

as far away as possible from the speaker wires.

Install and route the separately sold battery wire,

ground wire, speaker wires and the amplifier as

far away as possible from the antenna, antenna

cable and tuner.

· Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

Connecting the Unit

CAUTION

· Disconnect the negative () terminal of the battery

to avoid the risk of short-circuit and damage to

the unit.

· Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around it where they lie against metal parts.

· Do not route wires where they will get hot, for

example where the heater will blow over them. If

the insulation heats up, it may become damaged,

resulting in a short-circuit through the vehicle

body.

· Make sure that wires will not interfere with mov-

ing parts of the vehicle, such as the gearshift,

handbrake or seat sliding mechanism.

· Never feed power to other equipment by cutting

the insulation of the power supply wire to tap

from the wire. The current capacity of the wire

will be exceeded, causing overheating.

· Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

Setting the Unit

Connection Diagram

Bass Boost Frequency Control

You can select a bass boost frequency

from 40 to 120 Hz with the bass boost

control.

Power Indicator

The power indicator lights when the

power is switched on.

Bass Boost Level Control

Bass boost level control can boost the

level around the frequency selected by

the bass boost frequency control from 0

to 12 dB.

Cut Off Frequency Control for LPF

You can select a cut off frequency from

40 to 240 Hz.

Gain Control

If the sound level is too low, even when

the volume of the car stereo used along

with this power amplifier is turned up,

turn gain control on the front of the

power amplifier clockwise. If the sound

distorts when the volume is turned up,

turn the gain control counter-clockwise.

· When using with an RCA equipped car

stereo (standard output of 500 mV), set

to the NORMAL position. When using

with an RCA equipped Pioneer car

stereo with max. output of 4 V or

more, adjust level to match the car

stereo output level.

· For synced amplifier's gain control,

see the "Setting the Gain for synced

amplifier" section.

Slope Select Switch

You can select a slope for the LPF from

18 and 24 dB.

Subsonic Select Switch

The subsonic filter cuts inaudible fre-

quencies below 20 Hz to eliminate

unwanted vibrations and minimize

power loss.

MODE SELECT Switch

You can select amplifier's sync mode

from MASTER, SYNC and SYNC INV.

For the position of the MODE SELECT

switch, see the "Connecting the Speaker

wires" section.

Grommet

Battery wire (sold separately)

For the wire size, see the

"Connecting the Power Terminal"

section. The battery wire, the ground

wire and the optional direct ground

wire must be same size.

After making all other connections

at the amplifier, connect the battery

wire terminal of the amplifier to the

positive (+) terminal of the battery.

Ground wire (sold separately)

The ground wires must be same size

as the battery wire.

Connect to metal body or chassis.

Car stereo with

RCA output

jacks

External Output

(Subwoofer output)

Connecting wire with RCA

pin plugs (sold separately).

RCA input jack

Speaker terminal

See the "Connecting the

Speaker wires" section for

speaker connection instruc-

tions.

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control termi-

nal of the car stereo (SYSTEM REMOTE CONTROL). The female termi-

nal can be connected to the auto-antenna relay control terminal. If the car

stereo does not have a system remote control terminal, connect the male ter-

minal to the power terminal through the ignition switch.

Grommet

Reverse side

The maximum length

of the wire between the

fuse and the positive

(+) terminal of the bat-

tery is 45 cm (18 in.).

Positive (+)

terminal

Negative ()

terminal

Battery

Optional direct ground

wire (sold separately)

When chassis ground-

ing is not sufficient,

direct grounding

should be used. The

wire size should be

same size as the bat-

tery wire.

Fuse (150 A)

Each amplifier must be SEPARATELY

fused at 150 A.

SYNC OUTPUT /

SYNC INPUT jack

See the "Connecting the

Speaker wires" section

for SYNC OUTPUT /

SYNC INPUT jack con-

nection instructions.

Connecting the Unit

Connecting the Power Terminal

· Always use the recommended battery and ground

wire, which is sold separately. Connect the battery

wire directly to the car battery positive terminal

(+) and the ground wire to the car body.

· Recommended wires size (AWG: American Wire

Gauge) is as follows. The battery wire, the ground

wire and the optional direct ground wire must be

same size.

Battery Wire and Ground Wire Size

Wire Length

less than 4 ft

4--7 ft

7--10 ft

less than 1.2 m

1.2--2.1 m

2.1--3.0 m

Wire Size

4 AWG

2 AWG

10--13 ft

13--16 ft

16--19 ft

19--22 ft

3.0--3.9 m

3.9--4.8 m

4.8--5.7 m

5.7--6.7 m

2 AWG

1 AWG

0 AWG

1. Pass the battery wire from the

engine compartment to the interior

of the vehicle.

· After making all other connections to the

amplifier, connect the battery wire terminal of

the amplifier to the positive (+) terminal of

the battery.

2. Twist the battery wire, ground wire

and system remote control wire.

3. Connect the wires to the terminal.

· Before connecting the wires to the terminals,

remove the endcap. After connecting the

wires to the terminals, attach the endcap.

· Fix the wires securely with the terminal

screws.

WARNING

Failure to securely fasten the battery wire to the ter-

minal using the terminal screws could cause the ter-

minal area to overheat and could result in damage

and injury including minor burns.

4. Put the wire ties in the slits and

wrap the wire ties around the wires.

· Wrap the wire tie around the wire insulation,

not the stripped wire.

Engine

compartment

Interior of

the vehicle

Drill a 14

mm (1/2 in.)

hole into the

vehicle body.

Insert the O-ring rubber

grommet into the vehicle

body.

Positive (+)

terminal

Twist

GND terminal

Power

terminal

Battery wire

System remote

control terminal

System remote

control wire

Ground wire

Fuse 150 A

Each amplifier must

be SEPARATELY

fused at 150 A.

The maximum length of the wire between

the fuse and the positive (+) terminal of the

battery is 45 cm (18 in.).

Endcap

Terminal

screw

Connecting the Speaker Terminals

1. Expose the end of the speaker wires

using nippers or a cutter by about

1520 mm (5/83/4 in.) and twist.

2. Connect the speaker wires to the

speaker terminals.

· Before connecting the wires to the terminals,

remove the endcap. After connecting the

wires to the terminals, attach the endcap.

· Fix the speaker wires securely with the termi-

nal screws.

3. Put the wire ties in the slits and

wrap the wire ties around the wires.

· Wrap the wire tie around the wire insulation,

not the stripped wire.

1520 mm

(5/83/4 in.)

Twist

Speaker terminal

Terminal screw

Speaker wire

Endcap

Setting the Gain for

synced amplifier

After connecting the speaker wires, adjust each

synced amplifier's gain control. All synced ampli-

fiers follow the master amplifier's settings.

Quick Setup of the Gain

Set each synced amplifier's gain control to the NOR-

MAL position. This setting will balance output vol-

umes sufficiently for most applications.

Advanced Setup of the Gain

Starting with the master amplifier, adjust the gain

control on each amplifier in order.

1. Output sin wave through this system at low output

level.

2. Use volt meter to measure the master amplifier's

output voltage level.

3. Use volt meter to measure the synced amplifier's

output voltage level.

4. Match the synced amplifier's output to the mas-

ter's output using the gain control on the synced

amplifier.

5. Repeat for the each synced amplifier in the proper

order.

Connecting the Speaker wires

Connect the speaker leads to suit the configuration according to the figures shown below and the next page.

Single Amplifier

· Speaker wire size must be 10 AWG minimum.

· Load may be any combination of speakers but impedance must be 2

or larger.

MODE SELECT switch must be in

MASTER position.

minimum

1,500 W

Two Amplifier Bridged

· Speaker wire size must be 10 AWG minimum.

· Load may be any combination of speakers but impedance must be 4

or larger.

Two Amplifier

· Speaker wire size must be 10 AWG minimum.

· Load may be any combination of speakers but impedance must be 2

or larger.

MODE SELECT switch must be in MASTER position.

minimum

3,000 W

MODE SELECT switch

must be in SYNC INV

position. Before setting

to the position, remove

the screw and the stop-

per.

Connecting wire with RCA

pin plugs (sold separately).

Connecting speaker wire

(sold separately).

minimum

1,500 W

minimum

1,500 W

MODE SELECT switch must be in MASTER position.

Connecting wire with

RCA pin plugs (sold

separately).

MODE SELECT

switch must be in

SYNC position.

Wire tie

Slit

Wire tie

Slit

Power source .............................................................................................................. 14.4 V DC (10.8 -- 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption .......................................................................................................... 70 A (at continuous power, 4

)

Average current drawn* .......................................................................................................... 10.6 A (4

for one channel)

15.6 A (2

for one channel)

Fuse ................................................................................................................................................................................ 150 A

Dimensions ........................................................................................................................ 300 (W)

× 64 (H) × 330 (D) mm

[12 (W)

× 3 (H) × 13 (D) in.

Weight ...................................................................................................... 7.3 kg (16.0 lbs.) (Leads for wiring not included)

Maximum power output ........................................................................................ 1,500 W

× 1 (4 ) / 3,000 W × 1 (2 )

Continuous power output .................................................................. 750 W

× 1 (at 14.4 V, 4 , 20 --240 Hz 1.0% THD)

1,500 W

× 1 (at 14.4 V, 2 , 20 --240 Hz 2.0% THD)

Load impedance .................................................................................... 4

(2 -- 8 allowable), (Ex. Bridge 4 -- 16 )

Frequency response ................................................................................................................ 10 -- 240 Hz (+0 dB, 1 dB)

S/N ratio ............................................................................................................................................ 90 dB (IHF-A network)

Distortion .......................................................................................................................................... 0.05 % (50 W, 100 Hz)

Low pass filter .................................................................................................................... Cut off frequency: 40 -- 240 Hz

Cut off slope: 18, 24 dB/oct

Subsonic filter (HPF) ................................................................................................................................ Frequency: 20 Hz

Slope: 18 dB

Bass boost .................................................................................................................................................. Level: 0 -- 12 dB

Frequency: 40 -- 120 Hz

Phase control .......................................................................................................................................... SYNC, SYNC INV

Gain control ................................................................................................................................................ 200 mV -- 6.5 V

Maximum input level / impedance ........................................................................................................ RCA: 6.5 V / 22 k

Note:

· Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

· The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

Specifications

CAUTION

· Do not install in:

--Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

--Places where it may interfere with the driver,

such as on the floor in front of the driver's seat.

· Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-circuit.

· Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Protect

all cables and important equipment such as fuel lines,

brake lines and electrical wiring from damage.

· Install tapping screws in such a way that the

screw tip does not touch any wire. This is important

to prevent wires from being cut by vibration of the

car, which can result in fire.

· DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

· To ensure proper installation, use the supplied parts

in the manner specified. If any parts other than the

supplied ones are used, they may damage internal

parts of the amplifier, or they may become loose

causing the amplifier to shut down.

· Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent malfunction and/or injury

· To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

--Allow adequate space above the amplifier for

proper ventilation.

--Do not cover the amplifier with a floor mat or

carpet.

· DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

· Do not install the amplifier on unstable places such

as the spare tire board.

· The best location for installation differs with the car

model and installation location. Secure the amplifier

at a sufficiently rigid location.

· Make temporary connections first and check that the

amplifier and the system operate properly.

· After installing the amplifier, confirm that the spare

tire, jack and tools can be easily removed.

Example of installation on the floor

mat or on the chassis

1. Place the amplifier where it is to be

installed. Insert the supplied tapping

screws (4

× 18 mm) into the screw

holes. Push on the screws with a

screwdriver so they make marks

where the installation holes are to be

located.

2. Drill 2.5 mm (1/8 in.) diameter holes

at the point marked, and install the

amplifier, either on the carpet or

directly to the chassis.

Installation

Drill a 2.5 mm (1/8 in.)

diameter hole

Tapping-screws

× 18 mm)

Floor mat

or chassis

Connecting the Unit

Four Amplifier

· Speaker wire size must be 10 AWG minimum.

· Load may be any combination of speakers but impedance must be 2

or larger.

minimum

1,500 W

minimum

1,500 W

minimum

1,500 W

minimum

1,500 W

Connecting wire with

RCA pin plugs (sold

separately).

Connecting wire with

RCA pin plugs (sold

separately).

Connecting wire with

RCA pin plugs (sold

separately).

MODE SELECT switch must

be in SYNC position.

MODE SELECT switch must

be in SYNC position.

MODE SELECT switch must

be in SYNC position.

MODE SELECT switch must be in MASTER position.

Four Amplifier Bridged

· Speaker wire size must be 10 AWG minimum.

· Load may be any combination of speakers but impedance must be 4

or larger.

MODE SELECT switch must be in MASTER position.

Connecting wire with

RCA pin plugs (sold

separately).

Connecting wire with

RCA pin plugs (sold

separately).

Connecting wire with

RCA pin plugs (sold

separately).

Connecting

speaker wire

(sold separately).

minimum

3,000 W

minimum

3,000 W

MODE SELECT switch

must be in SYNC INV

position. Before setting

to the position, remove

the screw and the stopper.

MODE SELECT switch

must be in SYNC INV

position. Before setting

to the position, remove

the screw and the stopper.

MODE SELECT switch

must be in SYNC INV

position. Before setting

to the position, remove

the screw and the stopper.

Connecting

speaker wire

(sold separately).

Power output ........................................................................................ 750 W RMS

× 1 channel

and 1 % THD+N)

1500 W RMS

× 1 channel

and 1 % THD+N, 240 Hz)

S/N ratio .............................................................................. 60 dBA (Reference: 1 W into 4

)

Cher Client:

La sélection d'un équipement audio de qualité comme l'unité que vous venez d'acheter n'est

que le début de votre plaisir musical. Maintenant, il est temps de penser à la manière de profiter au

maximum des plaisirs que vous offre votre équipement. Ce fabricant et le Groupe "Consumer

Electronics Group" de l'Association des Industries Electroniques veut que vous profitiez au maxi-

mum de votre équipement en l'utilisation à un niveau sûr. Un niveau qui permet au son d'être fort

et clair, sans beuglement ennuyant ou distorsion -- et, ce qui est plus important, sans affecter votre

ouïe sensible.

Le son peut être décevant. Avec le temps, le "niveau de confort" de votre ouïe s'adapte aux

volumes sonores plus élevés. Ainsi, les sons "normaux" peuvent en fait être forts et affecter votre

ouïe. Protégez-vous contre cela en réglant votre équipement à un niveau sûr AVANT l'adaptation

de votre ouïe.

Pour établir un niveau sûr:

Démarrer votre commande de volume à un réglage bas.

Augmentez lentement le son jusqu'à ce que vous l'entendiez confortablement et clairement,

sans distorsion.

Lorsque vous avez établi un niveau sonore confortable:

Réglez le cadran et laissez-le tel quel.

En prenant une minute pour faire cela, vous pourrez éviter des dommages ou des pertes de sen-

sibilités d'écoute dans le futur. Après tout, nous voulons que vous écoutiez pendant toute votre vie.

Nous voulons que vous écoutiez pendant toute votre vie

Utilisé avec sagesse, votre nouvel équipement sonore sera une source de plaisir pendant toute

votre vie. Comme les dommages de l'ouïe provenant d'un bruit fort ne sont souvent détectables

que lorsqu'il est trop tard, ce fabricant et le Groupe "Consumer Electronics Group" de

l'Association des Industries Electroniques vous recommandent d'éviter toute exposition prolongée

à un bruit excessif. Cette liste de niveaux sonores est incluse pour votre protection.

Niveau de

Décibels

Exemple

Bibliothèque tranquille, chuchotement

Salon, réfrigérateur, chambre à distance de la circulation

Circulation légère, conversation normale, bureau tranquille

Climatiseur à 20 pieds, machine à coudre

Aspirateur, sèche-cheveux, restaurant bruyant

Circulation moyenne en ville, évacuateurs de déchets, réveils à deux pieds.

LES BRUITS SUIVANTS PEUVENT ETRE DANGEREUX DANS LE CAS D'UNE EXPOSI-

TION CONSTANTE

Métro, motocyclette, circulation de camion, tondeuse à gazon

100

Collecteurs de poubelle, scie à chaîne, perceuse pneumatique

120

Concert de groupe rock devant les haut-parleurs, coup de tonnerre

140

Coup de pistolet, avion à réaction

180

Aire de lancement d'une fusée

Ces informations ont été gracieusement fournies par la Fondation de la Recherche pour les Sourds

Nous vous remercions d'avoir porté votre

choix sur un appareil PIONEER. Il a été

conçu et fabriqué pour vous apporter de

nombreuses années de satisfaction.

En raison des problèmes posés par

l'installation de cet appareil, Pioneer vous

conseille de consulter un professionnel.

Avant d'utiliser l'appareil, prenez

connaissance de ce mode d'emploi et tout

spécialement des AVERTISSEMENTS.

Pour toute question concernant cet

appareil, veuillez vous adresser au

revendeur ou à l'installateur.

Enregistrement du produit

Rendez-nous visite sur le site suivant:

1 Enregistrez votre produit. Nous conserverons sur

fichier les détails de votre achat pour vous

permettre de vous reporter à ces informations en

cas de déclaration de sinistre à votre assurance

pour perte ou vol.

2 Recevez les mises à jour sur les derniers produits

et les plus récentes technologies.

3 Téléchargez les manuels de l'utilisateur,

commandez les catalogues des produits,

recherchez de nouveaux produits, et bien plus.

Quelques mots concernant cet

appareil

Cet appareil est un amplificateur de classe

D pour haut-parleur d'extrême grave. Si les

deux canaux, L (gauche) et R (droit), sont

connectés à l'entrée cinch (RCA) de cet

appareil, la sortie est mixée parce que cet

appareil est un amplificateur monaural.

PRÉCAUTION

Ne remplacez pas le fusible par un fusible

de plus grande valeur ou de plus grand

calibre. L'utilisation d'un fusible inadapté

peut entraîner une surchauffe et de la

fumée, et peut provoquer l'endommage-

ment de l'appareil et des blessures, y

compris des brûlures.

Avant d'utiliser cet appareil

Service après-vente pour un

produit Pioneer

Pour toute question, et en particulier pour toute

question relative au service après-vente (y compris

celles qui relèvent de la garantie), veuillez vous

adresser au revendeur ou au distributeur auprès de

qui vous avez acquis ce produit. Dans l'hypothèse

où vous ne pourriez pas être renseigné comme

vous le désirez, consultez l'une des sociétés

mentionnées ci-dessous.

N'expédiez pas le produit à l'une de ces sociétés,

quelle qu'en soit la raison, avant d'y avoir été

expressément invité.

7 Etats-Unis

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

7 Canada

Pioneer électroniques du Canada, Inc.

Département de service aux consomma-

teurs

300 Allstate Parkway

Markham, Ontario L3R OP2

1-877-283-5901

Pour toute question concernant la garantie,

veuillez consulter le document Garantie Limitée

qui accompagne le produit.

ATTENTION

· Utilisez le câble de liaison à la batterie et le câble

de masse conseillés; ils sont vendus séparément.

Reliez le câble rouge à la borne positive (+) de la

batterie et le câble de masse à la carrosserie du

véhicule.

· Ne touchez pas l'amplificateur quand vous avez

les mains mouillées, faute de quoi vous risquez de

ressentir une secousse électrique. Pareillement, ne

touchez pas l'amplificateur s'il est mouillé.

· Pour votre sécurité et celles des autres usagers de

la route, maintenez le niveau d'écoute à une

valeur telle que les bruits de la circulation

demeurent nettement perceptibles.

· Vérifiez les raccordements de l'alimentation et du

haut-parleur d'extrêmes graves si le fusible du

câble de liaison (vendu séparément) à la batterie

vient à griller. Recherchez la cause de l'anomalie

puis corrigez-la; enfin, remplacez le fusible grillé

par un fusible de même taille et de même calibre.

· Pour éviter d'endommager l'amplificateur et du

haut-parleur d'extrême grave, le circuit de

protection coupe l'alimentation de l'amplificateur

(les sons ne sont plus émis) dès que survient une

situation anormale. Dans ce cas, mettez

l'ensemble des appareils hors tension et contrôlez

les liaisons entre l'amplificateur et du haut-parleur

d'extrême grave. Le cas échéant, recherchez la

cause de l'anomalie et corrigez-la.

· Consultez le revendeur si vous n'êtes pas en

mesure de résoudre le problème qui se pose à

vous.

· Pour éviter toute secousse électrique et tout risque

de court-circuit au cours des opérations de

raccordement et d'installation, n'oubliez pas de

débrancher le câble relié au pôle négatif de la

batterie () avant d'effectuer quelque opération

que ce soit.

· Avant d'effectuer un perçage requis par

l'installation de l'amplificateur, assurez-vous que

vous pouvez le faire sans danger pour les câbles,

canalisations, flexibles, etc., qui sont placés

derrière le panneau que vous devez percer.

· NE LAISSEZ PAS l'amplificateur entrer en

contact avec des liquides à cause, par exemple, de

l'emplacement où il a été placé. Cela pourrait

entraîner une secousse électrique. De plus, le

contact avec un liquide pourrait endommager

l'amplificateur et les enceintes, produire de la

fumée ou surchauffer l'appareil. Enfin, la surface

de l'amplificateur et des enceintes connectées peut

devenir chaude au toucher et entraîner de légères

brûlures.

Reviews

There are no reviews of this manual yet.

Related Products

Cover page of PIONEER DJM-909/WYXJ4 Service Manual

PIONEER PRS-D5000SPL/XH/UC Owner's Manual

Manual details

We guarantee that...

Sample pages

Reviews

Related Products

PIONEER DJM-909/WYXJ4 Service Manual

PIONEER DEH-3150UB/XN/ES1 Service Manual

PIONEER VSX-D2011-G/FXJI Owner's Manual

PIONEER DEH-1610 Owner's Manual

PIONEER XRP460F Owner's Manual

Popular Brands

General

Members Area