S-3EX
3
56
7
8
56
7
8
C
D
F
A
B
E
1.3 NETWORK ASSY
1.3.1 NETWORK ASSY FOR THE WOOFER
Fig. 2-3: Attachment specifications
of the Network Assy for the CST unit
Fig. 2-1: Input terminals (within the cabinet)
+: White/black line
-: White
From the Network Assy
for the woofer
From the Network Assy
for the CST unit
Apply adhesive.
Apply adhesive.
: Direction for
tightening a
screw
Fig. 2-4: Attachment specifications for the enclosure
plate (cross-sectional view of the speaker at the
location of the CST unit)
*The photo is of the Network Assy for the S-1EX,
but the structure for attachment is the same.
Enclosure plate
Chamber
Fig. 2-2: Attachment specifications
of the Network Assy for the woofer
Top
: Direction for
tightening a screw
FR
WN-1
8
4
Top
: Direction for
tightening a screw
FR
WN-1
8
5
· Network Assy for the woofer: After removing only the woofer, remove the Network Assy.
· Network Assy for the CST unit: After removing all speaker units, remove the Network Assy.
Tools to be used:
· Hexagonal wrench/4 mm: GGK1024
· Box wrench/14 mm: GGH-002
· DIABOND (black) (DB-1600WB): GYL-014
Before removing the Network Assy, first remove the grill and the speaker unit(s) then disconnect the cables connected to the
speaker unit.
The Network Assy is attached to the interior side of the right side
panel near the upper woofer with four screws.
(1) Remove the acoustic absorbent placed at the rear of the input
terminals. (See Figs. 2-5 and 2-6.)
(2) Remove the two nuts of the lower input terminals and
disconnect the round terminals. (See Fig. 2-1.)
(3) Remove the four screws that secure the Network Assy and pull
out the Network Assy through the hole for the woofer.
(See Fig. 2-2.)
(4) For reattachment of the Network Assy, pass it through the hole
for the woofer and secure it with the original four screws.
(See Fig. 2-2.)
(5) Connect the terminals of the cable coated with black tape
among the three pairs of cables coming from the Network Assy
to the lower input terminals and secure them with the nuts.
(6) Apply adhesive to the secured nuts. (Adhesive: DIABOND
black/GYL-014)
(7) Insert the acoustic absorbent at the rear of the input terminals.
(See Figs. 2-5 and 2-6.)
(8) Connect the terminals of the two pairs of cables coated with
white tape among the three pairs of cables coming from the
Network Assy to the input terminals of the woofer and solder
them. Then attach the woofer to the cabinet.
1.3.2 NETWORK ASSY FOR THE CST UNIT
The Network Assy is attached to the interior side of the left side
panel near the lower woofer with four screws.
(1) Remove the acoustic absorbent placed at the rear of the input
terminals, at the back within the chamber, and at the back of the
chamber. (See Figs. 2-5 to 2-8.)
(2) Remove the two nuts of the upper input terminals and discon
nect the round terminals. (See Fig. 2-1.)
(3) Remove the four screws that secure the enclosure plate from
within the chamber. Remove the four screws that secure the
Network Assy and pull out the Network Assy through the hole
for the woofer. (See Figs. 2-3 and 2-4.)
(4) For reattachment of the Network Assy, pass it through the hole
for the woofer and secure it with the original four screws.
(See Fig. 2-3.)
(5) Connect the round terminals of the cable among the cables
coming from the Network Assy to the upper input terminals and
secure them with the nuts.
(6) Apply adhesive to the secured nuts.
(Adhesive: DIABOND black/GYL-014)
(7) Pass the enclosure plate with two pairs of cables connected to
it from the rear of the chamber and secure the enclosure plate
to the plate from inside the chamber with the four original
screws. (See Fig. 2-4.)
(8) Place acoustic absorbent at the rear of the input terminals, at
the rear within the chamber, and at the rear of the chamber.
(See Figs. 2-5 to 2-8.)
(9) After making connection to the CST unit and soldering, attach
the cabinet.
