PIONEER S-81B-LR-K/SXTW/E5 Owner's Manual

PIONEER S-81B-LR-K/SXTW/E5 Owner's Manual
0 Rating(s)
Read reviews

Owner's Manual for PIONEER S-81B-LR-K/SXTW/E5, downloadable as a PDF file.

We also have service manual to this model.

Manual details

Immediate download after payment.
Delivered as a PDF file.
The manual has 54 pages
File size: 6.42 MB
Available language versions: Chinese Simplified, Danish, Italian, Norwegian, Portuguese, French, Swedish, English, Russian, Spanish, Dutch, German, Finnish
Different language versions may vary sligthly in file size and page count.

We guarantee that...

our manuals are complete,
our manuals are checked with antivirus,
We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

FRRD-234-A_S-81B-LR_En.book

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the

instructions, put them away in a safe place for future reference.

Before you start

· The nominal impedance of this speaker system is 6

Connect the speaker system to an amplifier with a load

impedance ranging from 6

to 16 (a model with "6 to

" displayed on the speaker output terminals).

In order to prevent damage to the speaker system resulting

from input overload, please observe the following precautions:

· Do not supply power to the speaker system in excess of the

maximum permissible input.

· When using a graphic equalizer to emphasize loud sounds

in the high-frequency range, do not use excessive amplifier

volume.

· Do not try to force a low-powered amplifier to produce loud

volumes of sound (the amplifier's harmonic distortion will

be increased, and you may damage the speaker).

Caution: installation

· Do not attach these speakers to the wall or ceiling. They may

fall off and cause injury.

· Do not install your speakers overhead on the ceiling or wall. If

improperly attached, the speaker grille can fall and cause

damage or personal injury.

· Switch off and unplug your AV equipment and consult the

instructions when connecting up components. Make sure you

use the correct connecting cables.

· The grille is affixed with magnets. The grille may fall if force is

applied to the grille in a horizontal direction. When cleaning

the speaker, remove the grille first.

Caution: in use

· Do not place the speaker on an unstable surface. It could

present a hazard if it falls, as well as damaging the equipment.

· Do not use the speaker to output distorted sound for long

periods of times. This can result in a fire hazard.

· Do not sit or stand on the speaker, or let children play on the

speaker.

· Do not put large or heavy objects on top of the speaker.

· Do not place magnetic objects such as screwdrivers or iron

parts near the tweeter or woofer. Since the speakers use

strong magnets, the objects may be attracted, causing injury

or damaging the diaphragm.

Cleaning the speaker cabinet

With normal use, wiping with a dry cloth should be sufficient to

keep the cabinet clean. If necessary, clean with a cloth dipped in

a neutral cleanser diluted five or six times with water, and wrung

out well. Do not use furniture wax or cleansers.

Never use thinners, benzine, insecticide sprays or other chemicals

on or near this unit since these will corrode the surfaces.

Cleaning the glossy finish of the speaker system

S-81B-LR-K only

· If you use a dusty or hard cloth or if you rub the screen hard,

the finish of the product will be scratched.

· If you clean the surface of the speaker system with a wet cloth,

water droplets on the surface may enter into the product,

resulting in malfunction.

· When cleaning the finish of the speaker system, gently wipe it

with a dry soft cloth; the supplied cleaning cloth.

What's in the box

Spikes x 6

Spike bases x 6

Non-skid pads x 8

Grille x 2

Cleaning cloth (for S-81B-LR-K only) x 1

Operating instructions

For U.S. model

For European model

WARNING: Handling the cord on this product or

cords associated with accessories sold with the

product will expose you to chemicals listed on

proposition 65 known to the State of California and

other governmental entities to cause cancer and

birth defect or other reproductive harm.

D36-P4_A_En

Wash hands after handling

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used

electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to

designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential

negative effects on the environment and human health.

K058_A_En

FRRD-234-A_S-81B-LR_En.book

English

How to install

Choosing where to place the speaker systems

· Sounds played through speaker systems are easily affected in

subtle ways by the conditions in the listening space.

· For best sound, choose a solid floor upon which to place the

speakers, and position the speakers as shown below. The level

of low sounds can be adjusted by moving the speakers closer

to or further from the wall. Adjust the speakers so that they are

equidistant from their respective side walls to assure balanced

sound.

· Place the left and right speakers equal distances from your

listening position for good stereo sound. Use speaker cords of

the same length for each speaker.

· So far as possible, place the front left and front right speakers

on the same plane as the TV screen.

· To achieve optimum surround sound, you should place the TV

between the left and right speakers, with the speakers

pointing at a 50 to 60 degree angle toward the listening

position.

· If the room has a lot of reverberation, we recommend hanging

heavy fabric on the walls, and/or putting a carpet on the floor

to damp the sound. For best results, cover walls completely.

· These speakers are bookshelf-type speakers which will give

their best performance when placed on a solid, level surface

off the floor. Placing the speakers directly on the floor will

result in boomy, undefined sound. Ideally, the tweeters should

be at about ear level when seated in your listening position.

We recommend using the CP-81B-K/MK speaker stand for

optimal sound and stability.

If you choose to use the CP-81B-K/MK speaker stand, make

sure you secure it with the screws provided.

(for more details, refer to the operating instructions of

CP-81B-K/MK)

· Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insufficient

reinforcement, misuse of the product, acts of nature, etc.

S-81B-LR-QL/W only

· The cabinet uses sliced veneer made of natural wood. Do not

place the speaker where it will be in direct sunlight, and avoid

positioning it near heaters and air conditioners. Doing so may

cause warping and discoloration of the speaker cabinet and

damage to the speaker.

When installing directly on the floor

Use the furnished spikes or non-skid pads when installing the

speaker directly on floor surface.

Using the spikes

This speaker system includes spikes that you can use to isolate

the speaker from the floor. Use the supplied spike bases to avoid

scratching the floor or other surface where the speaker is placed.

Twist the spikes into the threaded metal inserts

embedded in the bottom of the speaker.

Set the spike bases in the positions where the points of

the three spikes will strike when the speaker is set down.

Set the speaker on the spike bases and check to confirm

the speaker does not rock.

· Always use the spike bases as shown, with the indented

surface facing up to receive the spike point.

· It is very dangerous to try and set the spike while tilting the

speaker. Be sure to place the unit on a soft area (such as a

blanket) so that it does not damage the floor, and carry out the

installation with at least two people.

50 to 60

20 cm

(7 7/8 in.)

50 cm

(19 11/16 in.)

If you do not use the spike bases when placing the

speakers, the spikes may cause damage to the floor. If

you plan on using the spikes we highly recommend to

use the spike bases.

FRRD-234-A_S-81B-LR_En.book

Using the non-skid pads

To assure stable installation, affix the non-skid pads to the bottom

surface of the speaker base.

Attaching/removing the grille

This speaker system comes with grille which may be attached and

removed by:

To attach the grille, align the grille with the speaker body

and press gently.

To remove the grille, hold the grille with both hands near

the middle and pull gently toward you to separate the grille

from the speaker.

· Magnets are used for holding the grille in place. Do not place

the grilles near devices that may be susceptible to magnetic

influence (CRT televisions, etc.).

Connections

This speaker does not include speaker cables used for connecting

to an amplifier.

Connecting the cables

Switch off the power to your amplifier.

Connect the speaker cables to the input terminals on the

back of the speaker. For input terminal polarity, red is

positive (+) and black is negative ().

Loosen the knobs on the input terminals and insert the speaker

cable wires into each of the terminal post holes, then tighten the

knobs.

Connect the other ends of the cables to the amp's

speaker output terminals (for more details, refer to your amp

instrucion manual).

· You can also connect the speaker's terminals with a banana

plug. When using a banana plug, be sure to remove the cap at

the tip of the input terminal.

· After connecting the plugs, pull lightly on the cables to make

sure that the ends of the cables are securely connected to the

terminals. Poor connections can create noise and

interruptions in the sound.

· If the cables' wires happen to be pushed out of the terminals,

allowing the wires to come into contact with each other, it

places an excessive additional load on the amp. This may

cause the amp to stop functioning, and may even damage the

amp.

· When using a set of speakers connected to an amplifier, you

won't be able to obtain the normal stereo effect if the polarity

(

+, ) of one of the speakers (left or right) is reversed.

SPEAKERS

OUTPUT

Amplifier (rear)

Speaker (rear):

Input panel

Red

terminal (+)

Black

terminal (-)

Red terminal (+)

Black terminal (-)

CAUTION

These speaker terminals carry

HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

D3-4-2-2-3_A_En

FRRD-234-A_S-81B-LR_En.book

English

Specifications

Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex bookshelf type

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-way

Woofer/Tweeter . . . Coaxial unit: 13 cm (5 1/8 in.) cone/2.5 cm (1 in.) dome

Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Hz to 50 kHz

Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84.5 dB (2.83 V)

Maximum input power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 W

Crossover frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kHz

Exterior dimensions . . . . . . . 190 (W) mm x 350 (H) mm x 280 (D) mm

7 4/8 (W) in. x 13

13/

16 (H) in. x 11

16 (D) in.

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 kg (17 lbs 7 oz.)

Supplied accessories

Spikes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Spike bases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Grille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cleaning cloth (S-81B-LR-K only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operating instructions

· The S-81B-LR is shipped with two speaker systems included.

· Specifications and design subject to possible modification

without notice, due to improvements.

is a trademark placed on a product with Pioneer's Phase

Control technology. This technology enables high-grade sound

reproduction through each component by improving overall

phase matching.

Published by Pioneer Corporation.

S001_En

Selecting fine audio equipment such as the unit

you've just purchased is only the start of your

musical enjoyment. Now it's time to consider how

you can maximize the fun and excitement your

equipment offers. This manufacturer and the

Electronic Industries Association's Consumer

Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that

lets the sound come through loud and clear without

annoying blaring or distortion-and, most importantly,

without affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing

"comfort level" adapts to higher volumes of sound.

So what sounds "normal" can actually be loud and

harmful to your hearing. Guard against this by

setting your equipment at a safe level BEFORE your

hearing adapts.

To establish a safe level:

· Start your volume control at a low setting.

· Slowly increase the sound until you can hear it

comfortably and clearly, and without distortion.

Once you have established a comfortable sound

level:

· Set the dial and leave it there.

Taking a minute to do this now will help to prevent

hearing damage or loss in the future. After all, we

want you listening for a lifetime.

We Want You Listening For A Lifetime

Used wisely, your new sound equipment will

provide a lifetime of fun and enjoyment. Since

hearing damage from loud noise is often

undetectable until it is too late, this manufacturer

and the Electronic Industries Association's

Consumer Electronics Group recommend you avoid

prolonged exposure to excessive noise. This list of

sound levels is included for your protection.

Decibel

Level Example

Quiet library, soft whispers

Living room, refrigerator, bedroom away from traffic

Light traffic, normal conversation, quiet office

Air conditioner at 20 feet, sewing machine

Vacuum cleaner, hair dryer, noisy restaurant

Average city traffic, garbage disposals, alarm clock

at two feet.

THE FOLLOWING NOISES CAN BE DANGEROUS

UNDER CONSTANT EXPOSURE

Subway, motorcycle, truck traffic, lawn mower

100

Garbage truck, chain saw, pneumatic drill

120

Rock band concert in front of speakers,

thunderclap

140

Gunshot blast, jet plane

180

Rocket launching pad

Information courtesy of the Deafness Research Foundation.

For U.S. model

FRRD-234-A_S-81B-LR_En.book

Reviews

There are no reviews of this manual yet.

Related Products

Cover page of PIONEER CX-631 Service Manual

PIONEER S-81B-LR-K/SXTW/E5 Owner's Manual

Manual details

We guarantee that...

Sample pages

Reviews

Related Products

PIONEER CX-631 Service Manual

PIONEER DEH600 Service Manual

PIONEER DEH-P2650/XN/ES Owner's Manual

PIONEER SD-P5065-Q Owner's Manual

PIONEER DEH-P946 Service Manual

Popular Brands

General

Members Area