PIONEER S-STP600 Owner's Manual

Cover page of PIONEER S-STP600 Owner's Manual

Owner's Manual for PIONEER S-STP600, downloadable as a PDF file.

Manual details

  • Immediate download after payment.
  • Delivered as a PDF file.
  • The manual has 4 pages
  • File size: 0.26 MB
  • Available language versions: English
  • Different language versions may vary sligthly in file size and page count.

We guarantee that...

  • our manuals are complete,
  • our manuals are checked with antivirus,
  • We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

Thumbnail of page 1Thumbnail of page 2Thumbnail of page 3Thumbnail of page 4
Thumbnail of page 5Thumbnail of page 6Thumbnail of page 7Thumbnail of page 8
background image
What's in the box
Check that you have all the supplied accessories before you start:
· Front speakers x 2
· Center speaker x 1
· Surround speakers x 2 / Surround back speaker x 1
· Speaker cords x 1
· Non-skid pads
· Brackets for wall mounting x 5
· Screws x 5
· These operating instructions
Before you start
Thank you for buying this Pioneer product.
Please read through these operating instructions before installing
and using your speaker system.
Important
In order to prevent damage to the speaker system resulting from
input overload, please observe the following precautions:
· Do not supply signal to the speaker system in excess of the
maximum permissible input.
· When connecting or disconnecting cables, make sure that your
amplifier is switched off.
· Do not use excessive amplifier volume if using a tone control to
emphasize high or low frequencies.
Caution
· Do not connect the supplied speakers to any amplifier other
than the one supplied with this system. Connection to any other
smplifier may result in malfunction or fire.
· Pioneer will not be responsible for any accidents or damage that
may result from improper installation.
Making receiver settings
Before connecting the speakers, please read the Operating
Instructions supplied with your VSX-515 or VSX-815 receiver to make
the following settings:
· Switch the speaker impedance to the 6 setting (see Switching
the speaker impedance to do this).
· Set the crossover frequency to 200Hz (see Crossover network to
do this).
After connecting the speakers, please complete Using the Quick
Setup with the
6.1ch setting (refer to the receiver's 5 minute guide in
the supplied Operating Instructions).
Connecting the speakers
To get the best out of your speakers it is important that you connect
them properly to your amplifier or receiver. Each speaker
connection consists of a positive (+) and a negative (­) terminal.
These should be matched between the amplifier and the speaker.
Important
· Make sure all equipment is turned off before making any
connections.
1
Twist and pull off the protective shields on each speaker
wire.
2
Attach one end of the supplied speaker cord to the rear of
the center speaker.
Connect the wire with the colored marker to the red (+) terminal; the
plain wire to the black (­) terminal. Press down the spring-loaded
tab and insert the wire, as shown below. Release the tab to secure
the wire.
Red (+)
Black (­)
Green colored
marker
www.pioneerelectronics.com
OPERATING INSTRUCTIONS
S-STP600
SPEAKER SYSTEM
01 speaker system.fm 1
background image
What's in the box
Check that you have all the supplied accessories before you start:
· Front speakers x 2
· Center speaker x 1
· Surround speakers x 2 / Surround back speaker x 1
· Speaker cords x 1
· Non-skid pads
· Brackets for wall mounting x 5
· Screws x 5
· These operating instructions
Before you start
Thank you for buying this Pioneer product.
Please read through these operating instructions before installing
and using your speaker system.
Important
In order to prevent damage to the speaker system resulting from
input overload, please observe the following precautions:
· Do not supply signal to the speaker system in excess of the
maximum permissible input.
· When connecting or disconnecting cables, make sure that your
amplifier is switched off.
· Do not use excessive amplifier volume if using a tone control to
emphasize high or low frequencies.
Caution
· Do not connect the supplied speakers to any amplifier other
than the one supplied with this system. Connection to any other
smplifier may result in malfunction or fire.
· Pioneer will not be responsible for any accidents or damage that
may result from improper installation.
Making receiver settings
Before connecting the speakers, please read the Operating
Instructions supplied with your VSX-515 or VSX-815 receiver to make
the following settings:
· Switch the speaker impedance to the 6 setting (see Switching
the speaker impedance to do this).
· Set the crossover frequency to 200Hz (see Crossover network to
do this).
After connecting the speakers, please complete Using the Quick
Setup with the
6.1ch setting (refer to the receiver's 5 minute guide in
the supplied Operating Instructions).
Connecting the speakers
To get the best out of your speakers it is important that you connect
them properly to your amplifier or receiver. Each speaker
connection consists of a positive (+) and a negative (­) terminal.
These should be matched between the amplifier and the speaker.
Important
· Make sure all equipment is turned off before making any
connections.
1
Twist and pull off the protective shields on each speaker
wire.
2
Attach one end of the supplied speaker cord to the rear of
the center speaker.
Connect the wire with the colored marker to the red (+) terminal; the
plain wire to the black (­) terminal. Press down the spring-loaded
tab and insert the wire, as shown below. Release the tab to secure
the wire.
Red (+)
Black (­)
Green colored
marker
www.pioneerelectronics.com
OPERATING INSTRUCTIONS
S-STP600
SPEAKER SYSTEM
01 speaker system.fm 1
background image
3
Connect the other end of each speaker cable to your
receiver.
The speaker cables are color-coded for your convenience. Make sure
to match the speaker cable with the proper terminal (as indicated on
the rear of the receiver). See also the Operating Instructions that
came with your receiver.
· When connecting the surround back speaker, connect the
positive wire to the right channel (
+) terminal, and the negative
wire to the left channel (
­) terminal (see illustration).
Placing the speakers
The diagram below shows the standard speaker placement relative
to your listening position.
The following guidelines will help you to get the best performance
from your speaker system. See also the section on Connecting the
speakers in the Operating Instructions that came with your receiver.
· The distance between the front speakers should be about the
same as from your listening position to each speaker. Place
them at an equal distance either side of your TV and roughly at
ear-level (when you are seated in your usual listening position).
· You may want to angle the speakers slightly inward for better
image stability, especially for listeners who are not right in the
center.
· Placing the speakers close to the rear or side walls will enhance
the mid-bass performance, although too close (especially to a
corner) may result in boomy bass and degraded stereo image.
· The surround left, right and back speakers should all be placed
at about ear-level. Depending on the layout of your room, the
surround left and right speakers may be mounted on the side
walls, with the surround back speaker mounted on the rear wall.
· The surround back speaker should be placed directly behind
your listening position for best performance.
· Install the center speaker above or below the TV so that the
sound of the center channel is localized at the TV screen.
Important
· Do not attach the center speaker to the wall or ceiling. It may fall
off and cause injury. If you choose to install the center speaker
on top of the TV, be sure to secure it with tape or some other
suitable means. Otherwise, the speaker may fall from the TV due
to external shocks such as earthquakes, endangering those
nearby or damaging the speaker.
· Do not install speakers near a stove or other heating appliance,
or put them in a place exposed to the sun. Such locations may
cause the cabinet to change color and the speaker system to
break down.
· The front, center and surround speakers supplied with this
system are magnetically shielded. However, depending on the
installation location, color distortion may occur if the speaker is
installed extremely close to the screen of a television set. If this
happens, turn the television set off for 15 to 30 minutes before
switching it back on. If the problem persists, place the speaker
system away from the television set.
FRONT
RL
R
L
CENTER
SURROUND
RL
SURROUND BACK
SINGLE
S
P
E
A
K
E
R
S
SEE INSTRUCTION
MANUAL
Front right
Surround right
Surround left
Surround back
VSX-515/815
Front left
Center
Gray
Blue
White
Red
Green
Brown
Front left
Surround
left
Listening position
Center
Front right
Surround
right
Surround back
01 speaker system.fm 2
background image
Non-skid pads
Attach the non-skid pads to the base of the speakers. Use the
supplied adhesive to attach 4 pads to the base (flat surface) of each
speaker.
Cabinet maintenance
Use a polishing cloth or dry cloth to wipe off dust and dirt.
If the cabinet is very dirty, clean with a soft cloth dipped in some
neutral cleanser diluted five or six times with water, and then wipe
again with a dry cloth. Do not use furniture wax or cleaners.
Never use thinners, benzene, insecticide sprays and other
chemicals on or near the cabinets, since these will corrode the
surfaces.
Wall-mounting the front and surround speaker
system
Attaching the brackets
· Make sure to tighten the supplied screw as securely as possible
when attaching the bracket to the back of the speaker.
· Please do not attach the brackets to the center speaker.
Before mounting
· Remember that the speaker system is heavy and that its weight
could cause the wood screws to work loose, or the wall material
to fail to support it, resulting in the speaker falling. Make sure
that the wall on which you intend to mount the speakers is
strong enough to support them. Do not mount on plywood or
soft surface walls.
· Mounting screws are not supplied. Use screws that are suitable
for the wall material and that will support the weight of the
speaker.
Note
· If you are unsure of the qualities and strength of the walls,
consult a professional for advice.
· Pioneer is not responsible for any accidents or damage that
result from improper installation.
Troubleshooting
Caution
· These speakers are equipped with a protection device to protect
the transducers from extreme conditions. Under these
conditions the protection device will activate and stop the
speaker from producing sound. If this happens turn the volume
down to resume normal speaker output.
Specifications
Front / Surround / Surround back speakers
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.7 cm cone type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Hz to 20 kHz
Dimensions. . . . . . . . . . . . . . . . . . . . . . . .105 (W) x 115 (H) x 114 (D) mm
Weight
Front speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 kg
Surround speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.66 kg
Surround back speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.66 kg
Center speaker
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.7 cm 1-way system
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.7 cm cone type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Hz to 20 kHz
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . .270 (W) x 90 (H) x 100 (D) mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 kg
Note: Specifications and design subject to possible modification
without notice due to improvements.
5 ­ 7 mm
Mounting screw
(not supplied)
Bracket screw
(supplied)
5 mm
10 mm
Symptom
Possible cause
Remedy
No sound
· Bad speaker wire or
connection
· Receiver is off
· Volume control is at
zero
· Connect correctly or
replace wire.
· Turn on receiver.
· Slowly turn up volume.
Sound is
distorted
· Extreme signal
condition
· Turn down the
amplifier's output level
(volume, bass control,
bass boost) to lower the
level.
Speakers stop
producing
sound suddenly
· Extreme signal
condition for extended
period of time
· Turn the volume down
to resume normal
speaker output.
01 speaker system.fm 3
background image
<05G000001>
Printed in China
<SRD1304-A>
Published by Pioneer Corporation
Copyright ©2005 Pioneer Corporation
All rights reserved
Published by Pioneer Corporation
Copyright ©2005 Pioneer Corporation
All rights reserved
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
K002_A_En
01 speaker system.fm 4

Reviews

There are no reviews of this manual yet.