TEAC P-70 Owner's Manual

TEAC P-70 Owner's Manual
0 Rating(s)
Read reviews

Owner's Manual for TEAC P-70, downloadable as a PDF file.

We also have service manual to this model.

Manual details

Immediate download after payment.
Delivered as a PDF file.
The manual has 64 pages
File size: 1.77 MB
Available language versions: French, English, Spanish, Dutch, German, Italian
Different language versions may vary sligthly in file size and page count.

We guarantee that...

our manuals are complete,
our manuals are checked with antivirus,
We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

OWNER'S MANUAL

MANUEL DU PROPRIETAIRE

MANUAL DEL USUARIO

D00713000A

P-70

CD Drive Unit

ENGLISH

FRANÇAIS

ESPAÑOL

OWNER'S MANUAL

MANUEL DU PROPRIETAIRE

MANUAL DEL USUARIO

D00713000A

P-70

CD Drive Unit

ENGLISH

FRANÇAIS

ESPAÑOL

Important Safety Instructions

AC POWER CORD CONNECTION

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT.

CORDE DE CONNEXION CA

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU

FOND.

For CANADA

Pour le CANADA

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

· Reorient or relocate the equipment and/or the receiving

antenna.

· Increase the separation between the equipment and

receiver.

· Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

· Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to this equipments not expressly

approved by TEAC CORPORATION for compliance will void the

user's warranty.

For U.S.A.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution

when

moving

the

cart/apparatus combination to avoid

injury from tip-over.

13) Unplug this apparatus during lightning storms or when

unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

< Do not expose this apparatus to dripps or splashes.

< Do not place any objects filled with liquids, such as vases,

on the apparatus.

< Do not install this apparatus in a confined space such as a

book case or similar unit.

< The apparatus draws nominal non-operating power from the

AC outlet with its POWER switch in the off position.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated "dangerous voltage" within

the product's enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

WARNING : TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

Optical pickup :

Type

KSS-151A

Manufacturer :

SONY Corporation

Laser output

Less than 0.2 mW on the objective lens

Wavelength

760 - 800 nm

CAUTION

< DO NOT REMOVE THE PROTECTIVE HOUSING USING

SCREWDRIVER.

< USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

< IF THIS PRODUCT DEVELOPS TROUBLE, MAKE A CONTACT

WITH OUR SERVICEMAN, AND DO NOT USE THE PRODUCT IN

A TROUBLED STATE.

This product has been designed and manufactured according to

FDA regulations "title 21, CFR, chapter 1, subchapter J, based on

the Radiation Control for Health and Safety Act of 1968", and is

classified as class 1 laser product. There is not hazardous

invisible laser radiation during operation because invisible laser

radiation emitted inside of this product is completely confined in

the protective housings.

The label required in this regulation is shown

For U.S.A.

VARING: APPARATEN INNEHÅLLER LASER KOMPONENT MED

STRÅLNING ÖVERSTIGANDE KLASS 1.

"ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING NAR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSAETTELSE FOR STRÅLING"

"VAROITUS! SUOJAKOTELOA EI SAA AVATA. LAITE SISÄLTÄÄ

LASERDIODIN. JOKA LÄHETTÄ (NÄKYMÄTÖNTÄ) SILMILLE

VAARALLISTA LASERSÄTEILYÄ".

ADVARSEL: USYNLIG LASERBESTRÅLING NÅR DENNE DELEN ER

ÅPEN OG SIKKERHETSSPERREN ER UTKOBLET UNNGÅ

UTSETTELSE FOR STRÅLING.

IMPORTANT(for U.K.Customers)

DO NOT cut off the mains plug from this equipment. If the plug

fitted is not suitable for the power points in your home or the

cable is too short to reach a power point, then obtain an

appropriate safety approved extension lead or consult your

dealer.

If nonetheless the mains plug is cut off, remove the fuse and

dispose of the plug immediately, to avoid a possible shock

hazard by inadvertent connection to the mains supply.

If this product is not provided with a mains plug, or one has to be

fitted, then follow the instructions given below:

IMPORTANT. DO NOT make any connection to the larger

terminal which is marked with the letter E or by the safety earth

symbol | or coloured GREEN or GREEN-and-YELLOW.

The wires in the mains lead on this product are coloured in

accordance with the following code:

BLUE

: NEUTRAL

BROWN : LIVE

As these colours may not correspond with the coloured

markings identifying the terminals in your plug proceed as

follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

When replacing the fuse only a correctly rated approved type

should be used and be sure to re-fit the fuse cover.

IF IN DOUBT -- CONSULT A COMPETENT ELECTRICIAN.

Obs! nätströmställaren skiljer ej hela apparaten fran nätet.

Contents

Thank you for choosing TEAC. Read this manual carefully to get

the best performance from this unit.

Features

VRDS mechanism (employing a aluminum

tapered turntable and turntable bridge)

The VDRS assembly, though secure clamping to a turntable of

the same diameter as the disc being played, totally removes

unnecessary vibration; either from mechanical sources, or

from the typical vibration of a disc. Rigidity is also achieved

through the use of a turntable bridge composed of precision-

processed carbon tool steel. The shape of the turntable also

helps to correct any warp in the disc. Because of the precise

alignment of the optical axis produced by this arrangement,

the servo current is reduced. All of the above factors decrease

the disc read error rate, and help to prevent timing errors from

the clock circuit.

Word Sync

The P-70 can achieve word synchronization by accepting a

master clock from any suitably-equipped D/A converter. With

the converter acting as the master clock, any jitter resulting

from data transfer between the player and the converter is

essentially eliminated.

Twin-transformer structure, with the power

supply completely separated from the

mechanical and digital signal systems

To eliminate mutual interference, the important key

components of the player: power supply, mechanism control,

and digital system (word sync, frequency multiplier, and clock)

have been separated completely in the design. There are two

split-core transformers in the power supply for additional

interference rejection.

7 digital outputs, including 4 digital outputs

from the converter multiplier (2xFs, 4xFs)

The player has four (XLR x 2, RCA x 1, TOS x 1) digital output

terminals to handle the high-speed multiplied digital outputs

(2xFs:24 bits at 88.2kHz, 4xFs: 24 bits at 176.4kHz), in addition to

3 "standard" digital output terminals (RCA x 1, TOS x 2)

44.1kHz.

Following the dual AES specification, 4xFs (24bits at 176.4kHz)

audio is output from twin XLR terminals

The operational algorithm employed in the converter multiplier

circuit is the RDOT method; exclusive to TEAC Corporation.

High rigidity chassis and triangular pinpoint

feet

Based on 8 mm thick sheet steel, with the VRDS mechanism

attached directly, and employing H-type 20 mm thick extruded

aluminum. The front panel and the sides employ a construction

method in which the 1.6 mm thick sheets are first plated with

copper, and then with nickel. This two-layer design succeeds

in totally removing internal interference, and helps to optimize

the sonic performance.

With the triangular pinpoint feet composed of case-hardened

tool steel, vibration is almost completely eliminated.

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Names of Each Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

How to use the remote control unit . . . . . . . . . . . . . . . . . . . . . . 12

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Index searching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Playing back one track (single playback) . . . . . . . . . . . . . . . . . 16

Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Programmed Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Delete Programmed Playback . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Display type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

How to turn off the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Auto Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Timer playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

VRDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ENGLISH

Before Use

CAUTION

The product shall not be exposed to dripping or splashing and

that no object filled with liquids, such as vases, shall be placed

on the product.

Do not install this equipment in a confined space such as a

book case or similar unit.

Read this before operation

< As the unit may become warm during operation, always leave

sufficient space above the unit for ventilation.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

< Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Also

avoid locations subject to vibrations and excessive dust, heat,

cold or moisture.

< Do not place the unit on the amplifier/receiver.

< Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into

the set, contact your dealer.

< When removing the power plug from the wall outlet, always

pull directly on the plug, never yank the cord.

< To keep the laser pickup clean, do not touch it, and do not

forget to close the disc tray.

< Do not attempt to clean the unit with chemical solvents as this

might damage the finish. Use a clean, dry cloth.

< Keep this manual in a safe place for future reference.

DO NOT MOVE THE UNIT DURING PLAYBACK

During playback, the disc rotates at high speed. Do NOT lift or

move the unit during playback. Doing so may damage the disc.

WHEN MOVING THIS UNIT

When changing places of installation or packing the unit for

moving, be sure to remove the disc and return the disc table to

its original position in the player. Then, press the power switch

to turn the power off, and disconnect the power cord. Moving

this unit with the disc loaded may result in damage to this unit.

Beware of condensation

When the unit (or a disc) is moved from a cold to a warm place, or

used after a sudden temperature change, there is a danger of

condensation; vapor in the air could condense on the internal

mechanism, making correct operation impossible. To prevent this,

or if this occurs, leave the unit for one or two hours with the

power turned on. Then the unit will stabilize at the temperature of

its surroundings.

Maintenance

If the surface of the unit gets dirty, wipe with a soft cloth or use

diluted neutral cleaning liquid. Be sure to remove any fluid

completely. Do not use thinner, benzine or alcohol as they may

damage the surface of the unit.

Placement of the unit

High-quality hardened tool steel is used for the pin-point feet,

securely attached to the bottom of the player. Although the cover

feet may appear loose, the weight of the unit causes them to be

firm and secure, and the design effectively damps and reduces

vibration.

< Be careful to avoid injury when moving the unit, on account of

its weight. Get someone to help you if necessary.

< To protect floors, etc. you may stick the felt supplied with the

unit to the bottom of the cover feet.

Pin-point foot

Bottom plate

of the unit

Steel foot

Cover foot retaining screws

Cover foot

1. Place the unit on its side, left side down, as shown here.

2. Use the supplied tool and insert it into the hole on the bottom.

3. Turn the tool about 30 degrees counter-clockwise in the FREE

direction.

Securing the anti-vibration clamp

If you are going to transport the unit, you must secure the clamp

in position.

1. Remove any disc from the unit, disconnect the power, and

place the unit on its side, left side down, as shown here.

2. Use the supplied tool and insert it into the hole on the bottom.

3. Turn the tool about 30 degrees clockwise in the LOCK

direction.

NOTE:

You do not need to use force to clamp and unclamp the unit. This

may damage the unit. Use only the supplied tool and turn gently.

Releasing the anti-vibration clamp

When the P-70 is shipped from the factory, the pickup is secured

with an anti-vibration clamp in order to reduce vibration during

transport. This must be released before use.

Reviews

There are no reviews of this manual yet.

Related Products

TEAC P-70 Owner's Manual

Manual details

We guarantee that...

Sample pages

Reviews

Related Products

TEAC SZ1 Owner's Manual

TEAC RWH300 Owner's Manual

TEAC CD-X1700 Owner's Manual

TEAC DA-38 Service Manual

TEAC MC-DX22I Service Manual

Popular Brands

General

Members Area